Audio analog connection - Revision history

JeanLouisN at 17:07, 31 July 2011

2011-07-31T17:07:49Z

JeanLouisN at 17:02, 31 July 2011

2011-07-31T17:02:06Z

JeanLouisN: Precautions for using analog audio with APF27_Dev, avoidin short-circuiting the virtual ground

2011-07-31T16:53:34Z

Precautions for using analog audio with APF27_Dev, avoidin short-circuiting the virtual ground

JeanLouisN at 16:45, 31 July 2011

2011-07-31T16:45:31Z

JeanLouisN: New page: Connecting a simple stereo headphone and a seprate microphone to the '''APF27_Dev''' requires no special precaution. But there are some more complex configurations which may cause the aud...

2011-07-31T16:38:56Z

New page: Connecting a simple stereo headphone and a seprate microphone to the '''APF27_Dev''' requires no special precaution. But there are some more complex configurations which may cause the aud...

New page

Connecting a simple stereo headphone and a seprate microphone to the '''APF27_Dev''' requires no special precaution.

But there are some more complex configurations which may cause the audio output to refuse functioning with no visible cause, which are described below.
{{Note| The problems described here do not occur with the '''APF51_Dev''', which has no audio virtual ground.}}
== Electrical background ==
The output of an audio amplifier powered by a single positive voltage source presents normally a quiescent DC voltage of approximately half the power supply.

This DC voltage should never be applied to a loudspeaker, so the classical wiring involves a series capacitor to block this DC voltage (two capacitors for a stereo amplifier).

The capacitance value has to be large enough to preserve the lowest limit of the audio bandwidth (example : 220 uF for a 16 Ohm loudspeaker).

Another solution, avoiding the need of large capacitors, consists of creating a '''virtual ground''' for the speaker, the virtual ground is a DC voltage source with the same value as the quiescent voltage of the amplifier output.

The APF27_Dev board is designed to use the virtual ground available on the TS2101 audio chip.

The consequence is that the ground terminal of the audio output jack is connected to a 1.5V DC source (TS2101 VGND pin) instead of the board real ground.

{{Warning| It is not permitted to connect this virtual ground to the real ground, this would short-circuit the 1.5V source and cause the TS2101 to enter the "short-circuit protection mode" and stop audio output operation (see P. 28 of the TS2101 data sheet).}}

== Ground loop via mains earth ==

Here is an example of virtual ground short-circuit caused by the mains earth connection :
* the audio output of the APF27_dev is connected to a home stereo amplifier or any audio other audio equipement having a mains plug with earth connection
* the APF27_Dev has its ground connected to some equipement having a mains plug with earth connection, for example :
** the development PC, through the RS232 cable
** the power supply (AC adaptor) itself

==== suggested workarounds : ====
* unplug the RS232 cable
* use a power supply with no earth connection

{{Note| the Ethernet cable causes no ground loop, because it is isolated by transformers at both ends.}}

== Ground loop via the microphone jack ==

The audio input connector (microphone jack) of the APF27_Dev has its ground connected to the board's real ground.

Connecting together the grounds of both audio jacks causes a virtual ground short-circuit.

Examples :
* connecting the audio output and input to the same audio equipement, like an audio analog mixer
* connecting the audio output and input to a headset with microphone with common ground

==== suggested workaround : ====
* when both jacks are used, connect only the ground of the input jack, leaving the ground of the output jack unconnected
* then insert 2 capacitors in series with the audio outputs

← Older revision		Revision as of 17:02, 31 July 2011
Line 47:		Line 47:
	* when both jacks are used, connect only the ground of the input jack, leaving the ground of the output jack unconnected		* when both jacks are used, connect only the ground of the input jack, leaving the ground of the output jack unconnected
	* then insert 2 capacitors in series with the audio outputs		* then insert 2 capacitors in series with the audio outputs
		+	[[Category:Audio]]

← Older revision		Revision as of 16:53, 31 July 2011
Line 1:		Line 1:
		+	== Precautions for using analog audio with APF27_Dev ==
		+
	Connecting a simple stereo headphone and a separate microphone to the '''APF27_Dev''' requires no special precaution.		Connecting a simple stereo headphone and a separate microphone to the '''APF27_Dev''' requires no special precaution.

@@ Line 42: / Line 42: @@
 Examples :
 * connecting the audio output and input to the same audio equipement, like an audio analog mixer
-* connecting the audio output and input to a headset with microphone with common ground
+* connecting the audio output and input to a headset with microphone having common ground
 ==== suggested workaround : ====

@@ Line 1: / Line 1: @@
-Connecting a simple stereo headphone and a seprate microphone to the '''APF27_Dev''' requires no special precaution.
+Connecting a simple stereo headphone and a separate microphone to the '''APF27_Dev''' requires no special precaution.
 But there are some more complex configurations which may cause the audio output to refuse functioning with no visible cause, which are described below.
 {{Note| The problems described here do not occur with the '''APF51_Dev''', which has no audio virtual ground.}}
 == Electrical background ==
-The output of an audio amplifier powered by a single positive voltage source presents normally a quiescent DC voltage of approximately half the power supply.
+The output of an audio amplifier powered by a single positive voltage presents normally a quiescent DC voltage of approximately half the power supply.
 This DC voltage should never be applied to a loudspeaker, so the classical wiring involves a series capacitor to block this DC voltage (two capacitors for a stereo amplifier).
@@ Line 10: / Line 10: @@
 The capacitance value has to be large enough to preserve the lowest limit of the audio bandwidth (example : 220 uF for a 16 Ohm loudspeaker).
-Another solution, avoiding the need of large capacitors, consists of creating a '''virtual ground''' for the speaker, the virtual ground is a DC voltage source with the same value as the quiescent voltage of the amplifier output.
+Another solution, avoiding the need for large capacitors, consists of creating a '''virtual ground''' for the speaker, the virtual ground being a DC voltage source with the same value as the quiescent voltage of the amplifier output.
-The APF27_Dev board is designed to use the virtual ground available on the TS2101 audio chip.
+In this context, the APF27_Dev board is designed to use the virtual ground available on the TS2101 audio chip.
 The consequence is that the ground terminal of the audio output jack is connected to a 1.5V DC source (TS2101 VGND pin) instead of the board real ground.
@@ Line 21: / Line 21: @@
 Here is an example of virtual ground short-circuit caused by the mains earth connection :
-* the audio output of the APF27_dev is connected to a home stereo amplifier or any audio other audio equipement having a mains plug with earth connection
+* the audio output of the APF27_dev is connected to a home stereo amplifier or any other audio equipement having a mains plug with earth connection
 * the APF27_Dev has its ground connected to some equipement having a mains plug with earth connection, for example :
 ** the development PC, through the RS232 cable