Setup - Revision history

WikiSysop: /* Build and update your system */

2019-06-04T13:11:38Z

‎Build and update your system

JulienB: /* Build and update your system */

2018-08-03T12:59:39Z

‎Build and update your system

JulienB: /* First StartUp */

2018-08-03T12:57:11Z

‎First StartUp

FabienM: /* Build and update your system */

2017-07-06T07:12:17Z

‎Build and update your system

JulienB at 07:15, 22 November 2016

2016-11-22T07:15:27Z

JulienB: /* First StartUp */

2016-11-21T17:35:31Z

‎First StartUp

Salocin68 at 09:06, 17 December 2014

2014-12-17T09:06:53Z

Jorasse: /* Build and update your system */

2013-08-19T14:47:12Z

‎Build and update your system

Jorasse: /* Build and update your system */

2013-08-19T09:23:48Z

‎Build and update your system

Jorasse: /* Build and update your system */

2013-01-11T23:25:35Z

‎Build and update your system

@@ Line 31: / Line 31: @@
 BIOS> reset                 (then define ''ipaddr'' and ''serverip'')
 ...
-BIOS> run update_kernel
+BIOS> run update_kernel     (not needed on OPOS6UL* boards)
 BIOS> run update_rootfs
 </pre>
 }}

@@ Line 29: / Line 29: @@
 BIOS> reset
 BIOS> run flash_reset_env
 ...
 BIOS> run update_kernel

@@ Line 5: / Line 5: @@
 Follow these quick steps to setup your environment accordingly:
-# Plug your APF module in your development/docking board (custom one or Armadeus Systems official one) (your system will be hereafter referred to as "the Target")
+# Plug your APF/OPOS module in your development/docking board (custom one or Armadeus Systems official one) (your system will be hereafter referred to as "the Target").
 # '''On APF9328Dev/APF27Dev/PPS:''' connect your PC (= "the Host") to your board with a [http://en.wikipedia.org/wiki/Null_modem null-modem RS-232 cable] (only Rx/Tx/Gnd signals are needed). If you don't have a RS-232 port on your Host, you can use a "USB <-> serial" converter (you'll still need the null-modem cable).
-# '''On APF51Dev/APF28Dev/APF6Dev/OPOS6ULDev:''' connect your PC (= "the Host") to your board with a USB cable. On the devt board use the "Debug" miniUSB connector
+# '''On APF51Dev/APF28Dev/APF6Dev/OPOS6ULDev:''' connect your PC (= "the Host") to your board with a mini USB cable. On the devt board use the "Debug" connector.
-# [[Communicate | Install (minimum) tools to communicate with your APF/OPOS from your Host.]]
+# [[Communicate | On your Host PC, Install the (minimum) tools to communicate with your APF/OPOS.]]
 # Connect the power supply to your development board. (See the [[Datasheet]] of your *Dev board for more informations)
-# Verify your system is booting and starting Linux (In U-Boot console, type "boot" if bootdelay is too long). Several information will be displayed on your terminal like on this [[Linux start screenshot | screenshot]] (Default Linux login is "root" with an empty password). '''If your system is NOT starting''', walk through [[U-Boot communication quick check|this small checklist]].
+# Verify your system is booting and starting Linux (In U-Boot console, type "boot" if ''bootdelay'' is too long). Several information will be displayed on your terminal like on this [[Linux start screenshot | screenshot]] (Default Linux login is "root" with an empty password). '''If your system is NOT starting''', walk through [[U-Boot communication quick check|this small checklist]].
 # If Linux has successfully started, your system is operational. If you want to add applications to your board or develop custom ones, then you can proceed with the Toolchain installation. [[Setup#Build_and_update_your_system | See Build and update your system]].
 ===Tutorial===
-If you want a more "userfriendly" procedure, you can try this (under construction) tutorial: [[Beginner's_tutorial]]
+If you want a more "user friendly" procedure, you can try [[Beginner's_tutorial|this (under construction) tutorial]].
 ==Build and update your system==

← Older revision		Revision as of 07:12, 6 July 2017
Line 23:		Line 23:


−	{{Note\| When a board is shipped, default factory binaries are flashed on it. It can be a legacy version of the armadeus BSP. So it's important to load the latest release binaries ("Get latest release" menu on side bar of this wiki), or build them yourself, and update all software with the following commands (on U-Boot assuming the image files have already been copied in /tftpboot):	+	{{Note\| When a board is shipped, default factory binaries are flashed on it. It can be a legacy version of the armadeus BSP. So it's important to load the latest release binaries ("Get latest release" menu on side bar of this wiki), or build them yourself, and update all software with the following commands (on U-Boot assuming the image files have already been copied in /tftpboot, and [[Communicate#TFTP_server_installation \| tftpboot server is correctly installed on your host]]):

	<pre class="apf">		<pre class="apf">

@@ Line 5: / Line 5: @@
 Follow these quick steps to setup your environment accordingly:
-# Plug your APF module in your development/docking board (custom one or ARMadeus Systems official one) (your system will be hereafter referred to as "the Target")
+# Plug your APF module in your development/docking board (custom one or Armadeus Systems official one) (your system will be hereafter referred to as "the Target")
 # '''On APF9328Dev/APF27Dev/PPS:''' connect your PC (= "the Host") to your board with a [http://en.wikipedia.org/wiki/Null_modem null-modem RS-232 cable] (only Rx/Tx/Gnd signals are needed). If you don't have a RS-232 port on your Host, you can use a "USB <-> serial" converter (you'll still need the null-modem cable).
-# '''On APF51Dev/APF28Dev/APF6Dev:''' connect your PC (= "the Host") to your board with a USB to miniUSB cable. On the APF use the "Debug" connector (between HDMI and USB Host ones)
+# '''On APF51Dev/APF28Dev/APF6Dev/OPOS6ULDev:''' connect your PC (= "the Host") to your board with a USB cable. On the devt board use the "Debug" miniUSB connector
-# [[Communicate | Install (minimum) tools to communicate with your APF from your Host.]]
+# [[Communicate | Install (minimum) tools to communicate with your APF/OPOS from your Host.]]
 # Connect the power supply to your development board. (See the [[Datasheet]] of your *Dev board for more informations)
 # Verify your system is booting and starting Linux (In U-Boot console, type "boot" if bootdelay is too long). Several information will be displayed on your terminal like on this [[Linux start screenshot | screenshot]] (Default Linux login is "root" with an empty password). '''If your system is NOT starting''', walk through [[U-Boot communication quick check|this small checklist]].

@@ Line 2: / Line 2: @@
 ==First StartUp==
-Just got your Armadeus board and want to start playing with it? <br>
+Just got your Armadeus development kit and want to start playing with it?
 Follow these quick steps to setup your environment accordingly:
-# Connect your APF module to your development/docking board (custom one or ARMadeus Systems official one) (your system will be hereafter referred to as "the Target")
+# Plug your APF module in your development/docking board (custom one or ARMadeus Systems official one) (your system will be hereafter referred to as "the Target")
 # '''On APF9328Dev/APF27Dev/PPS:''' connect your PC (= "the Host") to your board with a [http://en.wikipedia.org/wiki/Null_modem null-modem RS-232 cable] (only Rx/Tx/Gnd signals are needed). If you don't have a RS-232 port on your Host, you can use a "USB <-> serial" converter (you'll still need the null-modem cable).
 # '''On APF51Dev/APF28Dev/APF6Dev:''' connect your PC (= "the Host") to your board with a USB to miniUSB cable. On the APF use the "Debug" connector (between HDMI and USB Host ones)

← Older revision		Revision as of 14:47, 19 August 2013
Line 22:		Line 22:


−	{{Note\| When a board is shipped, default factory binaries are flashed on it. It can be a legacy version of the armadeus BSP. So it's important to load the latest release binaries ("Get latest release" menu on side bar of this wiki), or build them yourself, and update all software with the following commands (on U-Boot):	+	{{Note\| When a board is shipped, default factory binaries are flashed on it. It can be a legacy version of the armadeus BSP. So it's important to load the latest release binaries ("Get latest release" menu on side bar of this wiki), or build them yourself, and update all software with the following commands (on U-Boot assuming the image files have already been copied in /tftpboot):

	<pre class="apf">		<pre class="apf">

@@ Line 26: / Line 26: @@
 <pre class="apf">
 BIOS> run update_uboot
 BIOS> reset
 ...
 BIOS> run update_kernel

← Older revision		Revision as of 23:25, 11 January 2013
Line 22:		Line 22:


−	{{Note\| When a board is shipped, default factory binaries are flashed on it. It can be ~~an old~~ version of the armadeus BSP. So it's important to load the latest release binaries ("Get latest release" menu on side bar of this wiki), or build them yourself, and update all software with the following commands (on U-Boot):	+	{{Note\| When a board is shipped, default factory binaries are flashed on it. It can be a legacy version of the armadeus BSP. So it's important to load the latest release binaries ("Get latest release" menu on side bar of this wiki), or build them yourself, and update all software with the following commands (on U-Boot):

	<pre class="apf">		<pre class="apf">