Vivado installation on Linux - Revision history

FabienM: /* HS3 */

2021-06-30T15:33:52Z

‎HS3

2021-06-30T15:32:05Z

‎JTaG probes

2021-06-30T15:31:54Z

2016-02-11T14:15:09Z

2015-03-17T13:29:34Z

‎Introduction

2015-02-12T15:28:44Z

‎Launch Vivado

2015-02-12T15:28:21Z

‎Requirements

2015-02-12T15:28:06Z

‎Launch install

2015-02-12T15:07:49Z

‎Requirements

2015-02-12T15:00:31Z

‎Download

@@ Line 62: / Line 62: @@
 Digilent provide a JTAG probe to configure Xilinx FPGA named [https://store.digilentinc.com/jtag-hs3-programming-cable/ HS3].
 == Links ==
 * [http://forums.xilinx.com/t5/Installation-and-Licensing/Run-Vivado-2013-4-on-Debian/td-p/407359 Run Vivado 2013.4 on Debian]

@@ Line 61: / Line 61: @@
 === HS3 ===
-Digilent provide a JTAG probe to configure Xilinx FPGA named [HS3 https://store.digilentinc.com/jtag-hs3-programming-cable/].
+Digilent provide a JTAG probe to configure Xilinx FPGA named [https://store.digilentinc.com/jtag-hs3-programming-cable/ HS3].
 == Links ==
 * [http://forums.xilinx.com/t5/Installation-and-Licensing/Run-Vivado-2013-4-on-Debian/td-p/407359 Run Vivado 2013.4 on Debian]

@@ Line 56: / Line 56: @@
 /opt/Xilinx/Vivado/2014.4$ ./bin/vivado
 </pre>
 == Links ==
 * [http://forums.xilinx.com/t5/Installation-and-Licensing/Run-Vivado-2013-4-on-Debian/td-p/407359 Run Vivado 2013.4 on Debian]

@@ Line 4: / Line 4: @@
 == Introduction ==
-Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new product. By default, no Armadeus board has some new Xilinx FPGA that could be targeted by Vivado. But with the new APF6 we can use Artix7 with PCIe on a daughter board (or with Xilinx dev-kit and APF6Dev PCIe connector) and enjoy the new Xilinx-tool.
+Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new Xilinx's products. By default no Armadeus board has a new FPGA supported by Vivado, but, with the APF6, we can use Artix7 on a daughter board (or with Xilinx dev-kit), thanks to PCIe, and enjoy this new Xilinx tool.
-This page is a tutorial to install Vivado on debian-linux host computer.
+This page is a tutorial on how to install Vivado on Debian Linux host computer.
-{{Note| Vivado can't be used with spartan products, it starts with "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...)}}
+{{Note| Vivado can't be used with Spartan products, it starts with the "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...)}}
 == Installation ==
@@ Line 14: / Line 14: @@
 * unsure that Bash is the default shell:
 <pre class="host">
 $ sudo dpkg-reconfigure dash

@@ Line 4: / Line 4: @@
 == Introduction ==
-Vivado is the new fpga design tool from Xilinx. It replace ISE and XPS tools for new product. By default, no Armadeus board has new Xilinx fpga that could be targeted by Vivado. But with the new APF6 we can use Artix7 with PCIe on a daughter board (or with Xilinx dev-kit and apf6dev pcie connector) and enjoy the new Xilinx-tool.
+Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new product. By default, no Armadeus board has some new Xilinx FPGA that could be targeted by Vivado. But with the new APF6 we can use Artix7 with PCIe on a daughter board (or with Xilinx dev-kit and APF6Dev PCIe connector) and enjoy the new Xilinx-tool.
 This page is a tutorial to install Vivado on debian-linux host computer.
-{{Note| Vivado can't be used with spartan products, it begin with 7 serie fpga (artix7, virtex7, zynq, kintex7, ...)}}
+{{Note| Vivado can't be used with spartan products, it starts with "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...)}}
 == Installation ==

@@ Line 35: / Line 35: @@
 * Fill forms then wait for about 20 minutes
-=== Launch Vivado ===
+== Launching Vivado ==
 * Go to the installed directory:

← Older revision		Revision as of 15:00, 12 February 2015
Line 10:		Line 10:

	== Installation ==		== Installation ==
		+
		+	=== Requirements ===
		+
		+	* unsure that Bash is the default shell:
		+	<pre class="host">
		+	$ sudo dpkg-reconfigure dash
		+	</pre>

	=== Download ===		=== Download ===