Difference between revisions of "DDR3-CycloneV interface description"

From ArmadeusWiki
Jump to: navigation, search
(Links)
(Clock)
 
(4 intermediate revisions by the same user not shown)
Line 18: Line 18:
 
|DDR3L
 
|DDR3L
 
|-
 
|-
|Speed
+
|Speed (DDR)
 
|750Mhz
 
|750Mhz
 
|-
 
|-
Line 32: Line 32:
  
 
== General description ==
 
== General description ==
{{Under_Construction}}
+
 
  
 
Diagram below describe the connections between the CycloneV and the two DDR3 blocks. Each DDR3 blocks has two banks of 128MB, on one chip (U15) all data are used, and on the other chip, only 128MB are used, the second bank is not plugged. Thus, the amount of ram accessible via the fpga is 384MB, with a data bus of 24bits.
 
Diagram below describe the connections between the CycloneV and the two DDR3 blocks. Each DDR3 blocks has two banks of 128MB, on one chip (U15) all data are used, and on the other chip, only 128MB are used, the second bank is not plugged. Thus, the amount of ram accessible via the fpga is 384MB, with a data bus of 24bits.
Line 90: Line 90:
 
{{Note| In one line :<pre class="host">$ find . -name "*_p0_pin_map.tcl" | xargs sed -iolt "/_mem_if_ddr3_emif_0_p0_get_input_clk_id {/a    return \$pll_output_node_id"</pre>}}
 
{{Note| In one line :<pre class="host">$ find . -name "*_p0_pin_map.tcl" | xargs sed -iolt "/_mem_if_ddr3_emif_0_p0_get_input_clk_id {/a    return \$pll_output_node_id"</pre>}}
  
== IO ==
+
=== Failed to find PLL reference clock ===
  
=== Pinout placement===
+
It's a known intel bug documented [https://www.altera.com/support/support-resources/knowledge-base/solutions/rd05282014_665.html here].
  
<source lang="tcl">
+
== IO ==
set_location_assignment PIN_C11 -to mem_a[0]
+
set_location_assignment PIN_B11 -to mem_a[1]
+
set_location_assignment PIN_A8 -to mem_a[2]
+
set_location_assignment PIN_A7 -to mem_a[3]
+
set_location_assignment PIN_D11 -to mem_a[4]
+
set_location_assignment PIN_E11 -to mem_a[5]
+
set_location_assignment PIN_F8 -to mem_a[6]
+
set_location_assignment PIN_E7 -to mem_a[7]
+
set_location_assignment PIN_D9 -to mem_a[8]
+
set_location_assignment PIN_D8 -to mem_a[9]
+
set_location_assignment PIN_B6 -to mem_a[10]
+
set_location_assignment PIN_B5 -to mem_a[11]
+
set_location_assignment PIN_C8 -to mem_a[12]
+
set_location_assignment PIN_B8 -to mem_a[13]
+
set_location_assignment PIN_H6 -to mem_a[14]
+
 
+
set_location_assignment PIN_C9 -to mem_ba[2]
+
set_location_assignment PIN_C10 -to mem_ba[1]
+
set_location_assignment PIN_C6 -to mem_ba[0]
+
 
+
set_location_assignment PIN_A10 -to mem_cas_n[0]
+
set_location_assignment PIN_J9 -to mem_ck[0]
+
set_location_assignment PIN_J8 -to mem_ck_n[0]
+
set_location_assignment PIN_H8 -to mem_cs_n[0]
+
 
+
set_location_assignment PIN_C21 -to mem_dm[2]
+
set_location_assignment PIN_C19 -to mem_dm[1]
+
set_location_assignment PIN_A15 -to mem_dm[0]
+
 
+
set_location_assignment PIN_C20 -to mem_dq[23]
+
set_location_assignment PIN_B20 -to mem_dq[22]
+
set_location_assignment PIN_D18 -to mem_dq[21]
+
set_location_assignment PIN_E17 -to mem_dq[20]
+
set_location_assignment PIN_A22 -to mem_dq[19]
+
set_location_assignment PIN_A20 -to mem_dq[18]
+
set_location_assignment PIN_E16 -to mem_dq[17]
+
set_location_assignment PIN_D17 -to mem_dq[16]
+
 
+
set_location_assignment PIN_C18 -to mem_dq[15]
+
set_location_assignment PIN_B16 -to mem_dq[14]
+
set_location_assignment PIN_C16 -to mem_dq[13]
+
set_location_assignment PIN_C15 -to mem_dq[12]
+
set_location_assignment PIN_A17 -to mem_dq[11]
+
set_location_assignment PIN_B18 -to mem_dq[10]
+
set_location_assignment PIN_F15 -to mem_dq[9]
+
set_location_assignment PIN_E14 -to mem_dq[8]
+
set_location_assignment PIN_A14 -to mem_dq[7]
+
set_location_assignment PIN_C14 -to mem_dq[6]
+
set_location_assignment PIN_D13 -to mem_dq[5]
+
set_location_assignment PIN_C13 -to mem_dq[4]
+
set_location_assignment PIN_B13 -to mem_dq[3]
+
set_location_assignment PIN_B12 -to mem_dq[2]
+
set_location_assignment PIN_E12 -to mem_dq[1]
+
set_location_assignment PIN_F12 -to mem_dq[0]
+
 
+
set_location_assignment PIN_G15 -to mem_dqs[2]
+
set_location_assignment PIN_G14 -to mem_dqs_n[2]
+
 
+
set_location_assignment PIN_G12 -to mem_dqs[1]
+
set_location_assignment PIN_H12 -to mem_dqs_n[1]
+
 
+
set_location_assignment PIN_H9 -to mem_dqs[0]
+
set_location_assignment PIN_G8 -to mem_dqs_n[0]
+
 
+
set_location_assignment PIN_A13 -to mem_odt[0]
+
set_location_assignment PIN_B15 -to mem_cke[0]
+
set_location_assignment PIN_A9 -to mem_ras_n[0]
+
set_location_assignment PIN_E6 -to mem_we_n[0]
+
set_location_assignment PIN_B22 -to mem_reset_n
+
set_location_assignment PIN_A12 -to oct_rzqin
+
 
+
set_location_assignment PIN_T20 -to global_reset_n # Pulled-up on apf6sp
+
set_location_assignment PIN_H10 -to pll_ref_clk # Not Connected on apf6sp
+
set_location_assignment PIN_R16 -to soft_reset_n # Pulled-up on apf6sp
+
 
+
# Random pinout (not used)
+
set_location_assignment PIN_Y16 -to drv_status_fail
+
set_location_assignment PIN_H18 -to drv_status_pass
+
set_location_assignment PIN_V18 -to drv_status_test_complete
+
set_location_assignment PIN_J17 -to local_cal_fail
+
set_location_assignment PIN_J19 -to local_cal_success
+
set_location_assignment PIN_AA7 -to local_init_done
+
</source>
+
 
+
=== Technology pinout ===
+
 
+
<source lang="tcl">
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to oct_rzqin -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[3] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[3] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[3] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[4] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[4] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[4] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[5] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[5] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[5] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[6] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[6] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[6] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[7] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[7] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[7] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[8] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[8] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[8] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[9] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[9] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[9] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[10] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[10] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[10] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[11] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[11] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[11] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[12] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[12] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[12] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[13] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[13] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[13] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[14] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[14] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[14] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[15] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[15] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[15] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[16] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[16] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[16] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[17] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[17] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[17] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[18] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[18] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[18] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[19] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[19] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[19] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[20] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[20] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[20] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[21] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[21] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[21] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[22] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[22] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[22] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dq[23] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dq[23] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dq[23] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_dqs[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dqs[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dqs[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_dqs_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dqs_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dqs_n[0] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_dqs[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dqs[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dqs[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_dqs_n[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dqs_n[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dqs_n[1] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_dqs[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dqs[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dqs[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_dqs_n[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name INPUT_TERMINATION "PARALLEL 40 OHM WITH CALIBRATION" -to mem_dqs_n[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dqs_n[2] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_ck[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_ck[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "DIFFERENTIAL 1.35-V SSTL" -to mem_ck_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_ck_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[10] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[10] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[11] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[11] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[12] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[12] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[13] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[13] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[14] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[14] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[3] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[3] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[4] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[4] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[5] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[5] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[6] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[6] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[7] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[7] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[8] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[8] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_a[9] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_a[9] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_ba[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_ba[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_ba[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_ba[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_ba[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_ba[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_cas_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_cas_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_cke[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_cke[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_cs_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_cs_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_odt[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_odt[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_ras_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_ras_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_we_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_we_n[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_reset_n -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITHOUT CALIBRATION" -to mem_reset_n -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dm[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dm[0] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dm[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dm[1] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to mem_dm[2] -tag __ddr3_contr_example_if0_p0
+
set_instance_assignment -name OUTPUT_TERMINATION "SERIES 40 OHM WITH CALIBRATION" -to mem_dm[2] -tag __ddr3_contr_example_if0_p0
+
 
+
set_instance_assignment -name IO_STANDARD "SSTL-135" -to pll_ref_clk -tag __ddr3_contr_example_if0_p0
+
</source>
+
  
 +
* [[APF6_SP_DDR3_PINOUT#Pinout_placement | Pinout placement]]
 +
* [[APF6_SP_DDR3_PINOUT#Technology_pinout | Technology pinout]]
  
 
== Downloads ==
 
== Downloads ==
  
Soon here, some example project to downloads.
+
Soon here, some examples project to downloads.
  
 
== Links ==
 
== Links ==

Latest revision as of 12:21, 21 September 2017


Introduction

2 RAMs are connected to CycloneV's APF6_SP.

Parameters

  • DDR3:
MT41K128M16JT-125
part MT41K128M16JT-125
type DDR3L
Speed (DDR) 750Mhz
timings See verilog model provided by micron
JEDEC JEDEC DDR3-1600 -> JEDEC DDR3-1G6 2GB x8
Chip size 2048Mbits -> 128M x 16bits

General description

Diagram below describe the connections between the CycloneV and the two DDR3 blocks. Each DDR3 blocks has two banks of 128MB, on one chip (U15) all data are used, and on the other chip, only 128MB are used, the second bank is not plugged. Thus, the amount of ram accessible via the fpga is 384MB, with a data bus of 24bits.

DDR wiring diagram. Each green arrow is a 8 bits part of the data bus

To use the DDR3 SDRAM Controller with UniPhy provided by Quartus to instanciate the DDR3. See above how to do with Qsys.

DDR3 wiring for FPGA on apf6_sp

How to integrate DDR3 chips in Qsys

UniPhy Howto

This is a click howto configure the DDR3 controller in the APF6_SP.

  • Once the quartus project open, select your device correctly (see the product page to now the exact part name).
  • In the IP Catalog, select :
    installed IP->Library->Memory interfaces and Controllers->Memory Interfaces with UniPHY->DDR3 SDRAM Controller with UniPhy
  • In the right frame select :
    JEDEC DDR3-1G6 2GB x8
  • Then click on Apply
  • Select checkbox Enable Hard External Memory Interface (above the 6 configs tab).
  • Tab PHY Settings:
    • Speed grade : 8
    • Memory clock frequency : 375Mhz
    • PLL reference clock frequency : 62.5 Mhz
    • Rate on Avalon-MM Interface : Full
    • Supply voltage : 1.35V DDR3L
  • Tab Memory parameters
    • Memory device speed grade : 400Mhz
    • Total interface width : 24
    • Row address width : 14
  • Tab Controller Settings (Optionnal if you wan't to use the two DDR3 chip)
    • Select checkbox Expand Avalon-MM data for ECC
    • Select 48bits instead of 32
  • Finish
Note Note: Using 48bits instead 32 is not standard for avalon it can be harder to connect inside your design


Clock

The hard controller IP «DDR3 SDRAM Controller with UniPHY» require using and external oscillator to clock it. On APF6_SP, the all CycloneV fpga is clocked with the PCIe clock at 62.5Mhz by default.

To force Quartus to use the coreclkout as input clock for DDR3 controller a little hack must be done after HDL code is generated.

The DDR3 clock hack

Note Note: If you include the .qsys under your Quartus project, Quartus will regenerate all the Qsys HDL/TCL code each times you synthesize your design, and will erase the modification.
  1. Generate the design with Qsys
    1. Connect the pll_ref_clk of IP DDR3 SDRAM Controller with UniPHY on coreclkout of Avalon-MM Cyclone V Hard IP for PCI Express.
    2. Do all connections you need/want
    3. Generate the HDL code with Finish button.
  2. Under Quartus include the file your_project.qip and not your_project.qsys
    1. Find the file named *_p0_pin_map.tcl :
      $ find . -name "*_p0_pin_map.tcl"
    2. It must be under directory named your_project/synthesis/submodules/
    3. Edit it and looking for line begining with :
      proc YOUR_PROJECT_NAME_mem_if_ddr3_emif_0_p0_get_input_clk_id { pll_output_node_id } {
      
    4. Add this line at the begining of function :
      return $pll_output_node_id
      
    5. Then synthesize all.
Note Note: In one line :
$ find . -name "*_p0_pin_map.tcl" | xargs sed -iolt "/_mem_if_ddr3_emif_0_p0_get_input_clk_id {/a     return \$pll_output_node_id"


Failed to find PLL reference clock

It's a known intel bug documented here.

IO

Downloads

Soon here, some examples project to downloads.

Links