Difference between revisions of "ISP1761 Linux driver"
From ArmadeusWiki
(→Links) |
|||
| Line 1: | Line 1: | ||
This page summarizes the informations to use the [[ISP1761|DevFull's ISP1761 USB Host controller]] with Linux. | This page summarizes the informations to use the [[ISP1761|DevFull's ISP1761 USB Host controller]] with Linux. | ||
| − | + | = Compilation = | |
* Launch kernel configuration: | * Launch kernel configuration: | ||
$ make linux-menuconfig | $ make linux-menuconfig | ||
| Line 10: | Line 10: | ||
* then, depending on the devices you're planning to plug, you will have to [[USB_Host | add some more USB drivers.]] | * then, depending on the devices you're planning to plug, you will have to [[USB_Host | add some more USB drivers.]] | ||
| − | + | = Usage = | |
* Three drivers have to be started in order to get the ISP working. They have to be started in the following order: | * Three drivers have to be started in order to get the ISP working. They have to be started in the following order: | ||
# modprobe apf9328-isp1761 | # modprobe apf9328-isp1761 | ||
| Line 34: | Line 34: | ||
hub 1-1:1.0: 3 ports detected | hub 1-1:1.0: 3 ports detected | ||
| − | = | + | = Performances = |
A performance test has been performed by means of the usb_perf.sh script. <br> | A performance test has been performed by means of the usb_perf.sh script. <br> | ||
A high speed USB stick (corsair memory flash voyager) has been used. | A high speed USB stick (corsair memory flash voyager) has been used. | ||
Revision as of 19:55, 29 June 2008
This page summarizes the informations to use the DevFull's ISP1761 USB Host controller with Linux.
Contents
Compilation
- Launch kernel configuration:
$ make linux-menuconfig
- Activate USB support in Linux:
Device Drivers ---> USB support ---> <M> Support for Host-side USB
- and choose ISP1761 controller:
Device Drivers ---> Armadeus specific drivers ---> <M> isp1761 USB 2.0 Host controller
- then, depending on the devices you're planning to plug, you will have to add some more USB drivers.
Usage
- Three drivers have to be started in order to get the ISP working. They have to be started in the following order:
# modprobe apf9328-isp1761 # modprobe hal_imx # modprobe pehci
- or put them in a bash script in /etc/init.d:
#!/bin/sh modprobe apf9328-isp1761 modprobe hal_imx modprobe pehci
- and then you should see (on console):
isp1761 isp1761.0: PHILIPS ISP1761 isp1761 isp1761.0: new USB bus registered, assigned bus number 1 isp1761 isp1761.0: irq 138, io mem 0x00000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected /xxxx/armadeus_trunk/target/linux/modules/isp1761/hal/hal_imx.c: Registered Driver Philips /xxxx/armadeus_trunk/target/linux/modules/isp1761/host/pehci.c: Host Driver has been Registered # usb 1-1: new high speed USB device using isp1761 and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 3 ports detected
Performances
A performance test has been performed by means of the usb_perf.sh script.
A high speed USB stick (corsair memory flash voyager) has been used.
Test result (mean values): read -> 2980 kBytes/sec write -> 2095 kBytes/sec
The maximal bandwidth has been also measured by using a scope and by tranferring 4096 octets from the USBstick to a buffer of a kernel driver
Result: ~10Mo/sec
