Difference between revisions of "JTAG"
From ArmadeusWiki
(New page: I'm trying to get use of JTAG for U-Boot debugging and probably FPGA debugging in the future. This page is not yet finished, and the work is in progress. == Building a JTAG connector for ...) |
(→Building a JTAG connector for apf27Dev board) |
||
| Line 10: | Line 10: | ||
* 20-way flat cable, 1.27mm pitch (Conrad: 609463) | * 20-way flat cable, 1.27mm pitch (Conrad: 609463) | ||
| + | Assembling it all together: | ||
# Solder the 40-in header onto the J19 connector on the apf27dev board | # Solder the 40-in header onto the J19 connector on the apf27dev board | ||
# Cut off a ~10cm piece from the ATA cable with the 40pin plug at the end. | # Cut off a ~10cm piece from the ATA cable with the 40pin plug at the end. | ||
# Cut off ~10cm from 20-way flat cable | # Cut off ~10cm from 20-way flat cable | ||
# Carefully attach the 20-pin header to the flat cable. The thing is easy to break and it requires some forcing. Better buy a spare piece in advance. | # Carefully attach the 20-pin header to the flat cable. The thing is easy to break and it requires some forcing. Better buy a spare piece in advance. | ||
| − | # Use a knife and a cutting pad and dissect the cable endings, ~3cm long. | + | # Use a knife and a cutting pad and dissect the cable endings, ~3cm long. Dissect the whole width of the 20-way cable and only pins 40 to 31 on the 40-way ATA cable. |
# Strip the cable endings | # Strip the cable endings | ||
| − | # Solder the two cables together, as specified below | + | # Solder the two cables together, as specified below: |
| + | |||
| + | {| class="wikitable" border="1" | ||
| + | |- | ||
| + | ! ARM JTAG 20-pin cable | ||
| + | ! apf27 J19 40-pin cable | ||
| + | |- | ||
| + | | 1 - Vddh (+3.3v) | ||
| + | | 39 | ||
| + | |- | ||
| + | | 2 - Vddh (+3.3v) | ||
| + | | 39 | ||
| + | |- | ||
| + | | 3 - nTRST | ||
| + | | 33 | ||
| + | |- | ||
| + | | 4, 6, 8, 10, 12, 14, 16, 18, 20 - Vss (ground) | ||
| + | | 31, 34, 40 | ||
| + | |- | ||
| + | | 5 - TDI | ||
| + | | 35 | ||
| + | |- | ||
| + | | 7 - TMS | ||
| + | | 36 | ||
| + | |- | ||
| + | | 9 - TCK | ||
| + | | 37 | ||
| + | |- | ||
| + | | 13 –TDO | ||
| + | | 38 | ||
| + | |- | ||
| + | | 15 – nRST | ||
| + | | --- | ||
| + | |} | ||
Revision as of 01:00, 28 March 2009
I'm trying to get use of JTAG for U-Boot debugging and probably FPGA debugging in the future. This page is not yet finished, and the work is in progress.
Building a JTAG connector for apf27Dev board
List of material and part numbers at Conrad:
- 2x20-pin header, 2.54mm pitch (Conrad: 741973)
- ATA/IDE cable (Conrad: 971742)
- 2x10-pin IDC low profile header, 2.54mm pitch (Conrad: 743534)
- 20-way flat cable, 1.27mm pitch (Conrad: 609463)
Assembling it all together:
- Solder the 40-in header onto the J19 connector on the apf27dev board
- Cut off a ~10cm piece from the ATA cable with the 40pin plug at the end.
- Cut off ~10cm from 20-way flat cable
- Carefully attach the 20-pin header to the flat cable. The thing is easy to break and it requires some forcing. Better buy a spare piece in advance.
- Use a knife and a cutting pad and dissect the cable endings, ~3cm long. Dissect the whole width of the 20-way cable and only pins 40 to 31 on the 40-way ATA cable.
- Strip the cable endings
- Solder the two cables together, as specified below:
| ARM JTAG 20-pin cable | apf27 J19 40-pin cable |
|---|---|
| 1 - Vddh (+3.3v) | 39 |
| 2 - Vddh (+3.3v) | 39 |
| 3 - nTRST | 33 |
| 4, 6, 8, 10, 12, 14, 16, 18, 20 - Vss (ground) | 31, 34, 40 |
| 5 - TDI | 35 |
| 7 - TMS | 36 |
| 9 - TCK | 37 |
| 13 –TDO | 38 |
| 15 – nRST | --- |
