Difference between revisions of "Linux start screenshot"

From ArmadeusWiki
Jump to: navigation, search
(→‎Screenshot showing the serial text console during boot:)
Line 1: Line 1:
 
==Screenshot showing the serial text console during boot:==
 
==Screenshot showing the serial text console during boot:==
−
 
−
 
−
 
−
U-Boot 1.1.3 (Jan  8 2006 - 16:00:26) apm9328 patch 2.2
 
 
   
 
   
−
  U-Boot code: 0BF80000 -> 0BFA2264  BSS: -> 0BFA7014
+
  U-Boot 1.1.6 (Dec 18 2007 - 20:27:52) apx9328 patch 2.6
−
  RAM Configuration:
+
   
−
  Bank #0: 08000000 32 MB
+
  DRAM: 16 MB
−
  Flash: 16 MB
+
  Flash: 8 MB
 
  In:    serial
 
  In:    serial
 
  Out:  serial
 
  Out:  serial
 
  Err:  serial
 
  Err:  serial
 +
 +
Hit any key to stop autoboot:  0
 
  BIOS> boot
 
  BIOS> boot
−
  ""##"" Booting image at 100a0000 ...
+
  ## Booting image at 100a0000 ...
−
   Image Name:  Linux-2.6.12
+
   Image Name:  Linux-2.6.23.1
 +
  Created:      2007-12-18  19:33:05 UTC
 
   Image Type:  ARM Linux Kernel Image (uncompressed)
 
   Image Type:  ARM Linux Kernel Image (uncompressed)
−
   Data Size:    1028824 Bytes = 1004.7 kB
+
   Data Size:    1329440 Bytes = 1.3 MB
 
   Load Address: 08008000
 
   Load Address: 08008000
 
   Entry Point:  08008000
 
   Entry Point:  08008000
Line 24: Line 23:
 
  Starting kernel ...
 
  Starting kernel ...
 
   
 
   
−
  Uncompressing Linux.................................................................... done, booting the kernel.
+
  Uncompressing Linux....................................................................................... done, booting the kernel.
−
  Linux version 2.6.12 (eric@supin) (gcc version 3.4.3) #2 Fri Jan 27 21:14:03 CET 2006
+
  Linux version 2.6.23.1 (eric@shuttle) (gcc version 3.4.6) #1 PREEMPT Tue Dec 18 20:33:02 CET 2007
−
  CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
+
  CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
 +
Machine: Armadeus APF9328
 +
Memory policy: ECC disabled, Data cache writeback
 
  CPU0: D VIVT write-back cache
 
  CPU0: D VIVT write-back cache
 
  CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
 
  CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
 
  CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
 
  CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
−
Machine: Synertronixx scb9328
+
  Built 1 zonelists in Zone order.  Total pages: 4064
−
Memory policy: ECC disabled, Data cache writeback
+
  Kernel command line: console=ttySMX0,115200n8 mtdparts=apf9328_flash:256k(U-boot)ro,128k(U-boot_env),256k(firmware),1536k(kernel),6016k(root) root=/dev/mtdblock4 rootfstype=jffs2 ip=192.168.200.38:192.168.200.39:192.168.200.1:255.255.255.0:apm9328dev::off
−
  Built 1 zonelists
+
  PID hash table entries: 64 (order: 6, 256 bytes)
−
  Kernel command line: console=ttySMX0,115200n8   mtdparts=scb9328_flash:256k(U-boot)ro,128k(U-boot_env),256k(firmware),1m(kernel),6m(root),-(fs) root=/dev/mtdblock4 rootfstype=jffs2 ip=192.168.000.2:192.168.000.1:192.168.000.1:255.255.255.0:apm9328dev::off
+
−
  PID hash table entries: 256 (order: 8, 4096 bytes)
+
 
  Console: colour dummy device 80x30
 
  Console: colour dummy device 80x30
−
  Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
+
console [ttySMX0] enabled
−
  Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
+
  Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
−
  Memory: 32MB = 32MB total
+
  Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
−
  Memory: 30208KB available (1884K code, 214K data, 96K init)
+
  Memory: 16MB = 16MB total
 +
  Memory: 13420KB available (2472K code, 202K data, 100K init)
 
  Mount-cache hash table entries: 512
 
  Mount-cache hash table entries: 512
 
  CPU: Testing write buffer coherency: ok
 
  CPU: Testing write buffer coherency: ok
 
  NET: Registered protocol family 16
 
  NET: Registered protocol family 16
−
  JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
+
--- Registering APF9328 ressources
−
  Initializing Cryptographic API
+
Set apf9328_fb_info
 +
--- APF9328 ressources registered
 +
NET: Registered protocol family 2
 +
Time: imx_timer1 clocksource has been installed.
 +
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +
TCP established hash table entries: 512 (order: 0, 4096 bytes)
 +
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
 +
TCP: Hash tables configured (established 512 bind 512)
 +
TCP reno registered
 +
  JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
 +
  io scheduler noop registered
 +
io scheduler deadline registered (default)
 
  i.MX Framebuffer driver
 
  i.MX Framebuffer driver
−
  Console: switching to colour frame buffer device 30x40
+
  Console: switching to colour frame buffer device 40x30
−
apf9328_lcd_power: 1
+
 
  Serial: IMX driver
 
  Serial: IMX driver
−
  ttySMX0 at MMIO 0xe0006000 (irq = 30) is a IMX
+
  imx-uart.0: ttySMX0 at MMIO 0xe0006000 (irq = 30) is a IMX
−
  ttySMX1 at MMIO 0xe0007000 (irq = 24) is a IMX
+
  imx-uart.1: ttySMX1 at MMIO 0xe0007000 (irq = 24) is a IMX  
−
io scheduler noop registered
+
  RAMDISK driver initialized: 1 RAM disks of 2048K size 1024 blocksize
−
io scheduler deadline registered
+
−
io scheduler cfq registered
+
−
  RAMDISK driver initialized: 1 RAM disks of 4096K size 1024 blocksize
+
 
  dm9000 Ethernet Driver
 
  dm9000 Ethernet Driver
−
  eth0: dm9000 at edc3fffc,edc40000 IRQ 110 MAC: 00:0e:32:00:00:01
+
  eth0: dm9000 at c1850000,c1852002 IRQ 110 MAC: 00:0e:32:00:00:01
−
  Probing scb9328_flash at physical address 0x10000000 (16-bit buswidth)
+
physmap platform flash device: 10000000 at 10000000
−
  scb9328_flash: Found 1 x16 devices at 0x0 in 16-bit bank
+
physmap-flash physmap-flash.0: Could not reserve memory region
−
Intel/Sharp Extended Query Table at 0x0031
+
physmap-flash: probe of physmap-flash.0 failed with error -12
 +
  Probing apf9328_flash at physical address 0x10000000 (16 -bit buswidth)
 +
  apf9328_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 +
  Intel/Sharp Extended Query Table at 0x0031
 
  Using buffer write method
 
  Using buffer write method
 
  cfi_cmdset_0001: Erase suspend on write enabled
 
  cfi_cmdset_0001: Erase suspend on write enabled
−
  6 cmdlinepart partitions found on MTD device scb9328_flash
+
  5 cmdlinepart partitions found on MTD device apf9328_flash
−
  Creating 6 MTD partitions on "scb9328_flash":
+
  Creating 5 MTD partitions on "apf9328_flash":
 
  0x00000000-0x00040000 : "U-boot"
 
  0x00000000-0x00040000 : "U-boot"
 
  0x00040000-0x00060000 : "U-boot_env"
 
  0x00040000-0x00060000 : "U-boot_env"
 
  0x00060000-0x000a0000 : "firmware"
 
  0x00060000-0x000a0000 : "firmware"
−
  0x000a0000-0x001a0000 : "kernel"
+
  0x000a0000-0x00220000 : "kernel"
−
  0x001a0000-0x007a0000 : "root"
+
  0x00220000-0x00800000 : "root"
−
0x007a0000-0x01000000 : "fs"
+
 
  mice: PS/2 mouse device common for all mice
 
  mice: PS/2 mouse device common for all mice
−
  NET: Registered protocol family 2
+
  i2c /dev entries driver
−
IP: routing cache hash table of 512 buckets, 4Kbytes
+
  i.MX mmc driver
−
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
+
  TCP cubic registered
−
  TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
+
−
  TCP: Hash tables configured (established 2048 bind 2048)
+
 
  NET: Registered protocol family 1
 
  NET: Registered protocol family 1
 
  NET: Registered protocol family 17
 
  NET: Registered protocol family 17
−
  eth0: link down
+
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
 +
  eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
 +
imx-mmc imx-mmc.0: card removed
 
  IP-Config: Complete:
 
  IP-Config: Complete:
−
      device=eth0, addr=192.168.000.2, mask=255.255.255.0, gw=192.168.100.1,
+
      device=eth0, addr=192.168.200.38, mask=255.255.255.0, gw=192.168.200.1,
−
    host=apm9328dev, domain=, nis-domain=(none),
+
      host=apm9328dev, domain=, nis-domain=(none),
−
    bootserver=192.168.200.1, rootserver=192.168.200.1, rootpath=
+
      bootserver=192.168.200.39, rootserver=192.168.200.39, rootpath=
 
  VFS: Mounted root (jffs2 filesystem).
 
  VFS: Mounted root (jffs2 filesystem).
−
  Freeing init memory: 96K
+
  Freeing init memory: 100K
−
  Starting portmap daemon: portmap.
+
  init started: BusyBox v1.7.2 (2007-12-18 20:25:52 CET)
−
  eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
+
  starting pid 200, tty '': '/etc/init.d/rcS'
 +
Starting portmap: done
 
  Initializing random number generator... done.
 
  Initializing random number generator... done.
 
  Starting network...
 
  Starting network...
−
  Starting sshd: OK
+
  ifup: interface lo already configured
 +
Mounting all filesystems in /etc/fstab
 +
starting pid 219, tty '/dev/ttySMX0': '/sbin/getty'
 
   
 
   
 
   
 
   
−
Welcome to the Armadeus project.
 
 
   
 
   
 +
Welcome to the Armadeus development environment.
 
  armadeus login: root
 
  armadeus login: root
−
 
−
 
−
""BusyBox"" v1.01 (2006.01.27-18:50+0000) Built-in shell (ash)
 
−
Enter 'help' for a list of built-in commands.
 
−
 
 
  #
 
  #

Revision as of 19:47, 23 December 2007

Screenshot showing the serial text console during boot:

U-Boot 1.1.6 (Dec 18 2007 - 20:27:52) apx9328 patch 2.6

DRAM:  16 MB
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial

Hit any key to stop autoboot:  0 
BIOS> boot
## Booting image at 100a0000 ...
  Image Name:   Linux-2.6.23.1
  Created:      2007-12-18  19:33:05 UTC
  Image Type:   ARM Linux Kernel Image (uncompressed)
  Data Size:    1329440 Bytes =  1.3 MB
  Load Address: 08008000
  Entry Point:  08008000
  Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux....................................................................................... done, booting the kernel.
Linux version 2.6.23.1 (eric@shuttle) (gcc version 3.4.6) #1 PREEMPT Tue Dec 18 20:33:02 CET 2007
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: Armadeus APF9328
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order.  Total pages: 4064
Kernel command line: console=ttySMX0,115200n8 mtdparts=apf9328_flash:256k(U-boot)ro,128k(U-boot_env),256k(firmware),1536k(kernel),6016k(root) root=/dev/mtdblock4 rootfstype=jffs2 ip=192.168.200.38:192.168.200.39:192.168.200.1:255.255.255.0:apm9328dev::off
PID hash table entries: 64 (order: 6, 256 bytes)
Console: colour dummy device 80x30
console [ttySMX0] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 16MB = 16MB total
Memory: 13420KB available (2472K code, 202K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
--- Registering APF9328 ressources
Set apf9328_fb_info
--- APF9328 ressources registered
NET: Registered protocol family 2
Time: imx_timer1 clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
i.MX Framebuffer driver
Console: switching to colour frame buffer device 40x30
Serial: IMX driver
imx-uart.0: ttySMX0 at MMIO 0xe0006000 (irq = 30) is a IMX
imx-uart.1: ttySMX1 at MMIO 0xe0007000 (irq = 24) is a IMX 
RAMDISK driver initialized: 1 RAM disks of 2048K size 1024 blocksize
dm9000 Ethernet Driver
eth0: dm9000 at c1850000,c1852002 IRQ 110 MAC: 00:0e:32:00:00:01
physmap platform flash device: 10000000 at 10000000
physmap-flash physmap-flash.0: Could not reserve memory region
physmap-flash: probe of physmap-flash.0 failed with error -12
Probing apf9328_flash at physical address 0x10000000 (16 -bit buswidth)
apf9328_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
5 cmdlinepart partitions found on MTD device apf9328_flash
Creating 5 MTD partitions on "apf9328_flash":
0x00000000-0x00040000 : "U-boot"
0x00040000-0x00060000 : "U-boot_env"
0x00060000-0x000a0000 : "firmware"
0x000a0000-0x00220000 : "kernel"
0x00220000-0x00800000 : "root"
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i.MX mmc driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
imx-mmc imx-mmc.0: card removed
IP-Config: Complete:
      device=eth0, addr=192.168.200.38, mask=255.255.255.0, gw=192.168.200.1,
     host=apm9328dev, domain=, nis-domain=(none),
     bootserver=192.168.200.39, rootserver=192.168.200.39, rootpath=
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 100K
init started: BusyBox v1.7.2 (2007-12-18 20:25:52 CET)
starting pid 200, tty : '/etc/init.d/rcS'
Starting portmap: done
Initializing random number generator... done.
Starting network...
ifup: interface lo already configured
Mounting all filesystems in /etc/fstab
starting pid 219, tty '/dev/ttySMX0': '/sbin/getty'



Welcome to the Armadeus development environment.
armadeus login: root
#
Retrieved from "http://www.armadeus.org/wiki/index.php?title=Linux_start_screenshot&oldid=3291"