Difference between revisions of "Serial Transfer"
From ArmadeusWiki
(→Usage) |
(→TBDL) |
||
| (8 intermediate revisions by the same user not shown) | |||
| Line 9: | Line 9: | ||
==Installation== | ==Installation== | ||
| − | + | ===Target (APF)=== | |
Modify your Buildroot configuration: | Modify your Buildroot configuration: | ||
<pre class="host"> | <pre class="host"> | ||
$ make menuconfig | $ make menuconfig | ||
</pre> | </pre> | ||
| − | to add lrzsz package: | + | to add lrzsz package: |
| − | + | ||
| − | + | ||
| − | + | ||
<pre class="config"> | <pre class="config"> | ||
| − | [*] lrzsz | + | Package Selection for the target ---> |
| + | Networking applications ---> | ||
| + | [*] lrzsz | ||
</pre> | </pre> | ||
and then rebuild your rootfs: | and then rebuild your rootfs: | ||
| Line 28: | Line 27: | ||
Reflash it or manually copy ''rz'' and ''sz'' executables found in ''$ARMADEUS_ROOTFS_DIR/usr/bin/''. | Reflash it or manually copy ''rz'' and ''sz'' executables found in ''$ARMADEUS_ROOTFS_DIR/usr/bin/''. | ||
| − | + | ===Host=== | |
| − | Install lrzsz package, if not already installed on your system. For example on Ubuntu/Debian: | + | * Install lrzsz package, if not already installed on your system. For example on Ubuntu/Debian: |
| + | <pre class="host"> | ||
$ sudo apt-get install lrzsz | $ sudo apt-get install lrzsz | ||
| + | </pre> | ||
| + | * Install minicom tool: | ||
| + | <pre class="host"> | ||
| + | $ sudo apt-get install minicom | ||
| + | </pre> | ||
| + | * The first time, configure minicom (as root): | ||
| + | <pre class="host"> | ||
| + | $ sudo minicom -s | ||
| + | </pre> | ||
==Usage== | ==Usage== | ||
| − | {{Warning| You must use minicom as serial terminal and not kermit | + | {{Warning| You must use minicom as serial terminal and not kermit, sorry ! :-(}} |
| − | Be sure to have correctly configured Minicom (line speed, 8N1, no flow control, and correct download/upload directories path). | + | * Be sure to have correctly configured Minicom (line speed, 8N1, no flow control, and correct download/upload directories path). |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
* Use '''rz''' for receiving and '''sz''' to send files: | * Use '''rz''' for receiving and '''sz''' to send files: | ||
| − | ===Host --> Target=== | + | ===Host (PC) --> Target (APF)=== |
<pre class="apf"> | <pre class="apf"> | ||
# cd /whereToPutTheFileOnTheTarget/ | # cd /whereToPutTheFileOnTheTarget/ | ||
| Line 49: | Line 52: | ||
.. waiting to receive. | .. waiting to receive. | ||
</pre> | </pre> | ||
| − | then in minicom do: '''Ctrl+A , s''' and choose zmodem protocol and the file to send. | + | * then in minicom do: '''Ctrl+A , s''' and choose zmodem protocol and the file to send. |
| − | Wait a little and your file will be copied to your board rootfs ! ;-) | + | * Wait a little and your file will be copied to your board rootfs ! ;-) |
| − | ===Target --> Host=== | + | ===Target (APF) --> Host (PC)=== |
<pre class="apf"> | <pre class="apf"> | ||
| − | # cd / | + | # cd /location/of_the/file_to_send/on_the_apf/ |
# sz -b --zmodem filename | # sz -b --zmodem filename | ||
</pre> | </pre> | ||
| − | Minicom handles the file receiving automatically (and put it in your $HOME by default) | + | Minicom handles the file receiving automatically (and put it in your $HOME by default, or the directory you configured in Minicom: Ctrl+z, o, ''Filenames and paths'', ''Download directory'') |
==TBDL== | ==TBDL== | ||
| + | ===Serial transfer through USB gadget as serial link=== | ||
| + | After having booted your board: | ||
| + | * On your Target, open a new terminal on your serial link (here USB): | ||
| + | <pre class="apf"> | ||
| + | # /sbin/getty -L ttygserial 115200 vt100 | ||
| + | </pre> | ||
| + | * On your Host, launch Minicom and configure it to use ''/dev/ttyUSB1'' at 115200, then connect it to this terminal | ||
| + | |||
| + | ==Transfer without terminal== | ||
| + | * On your Target, launch receiving: | ||
| + | <pre class="apf"> | ||
| + | # rz --zmodem 1>/dev/ttyXXX 0</dev/ttyXXX | ||
| + | </pre> | ||
| + | * On your Host, launch transfer: | ||
| + | <pre class="host"> | ||
| + | $ sz --zmodem /tftpboot/afiletosend 1>/dev/ttyUSB1 0</dev/ttyUSB1 | ||
| + | </pre> | ||
==Links== | ==Links== | ||
Revision as of 12:44, 29 November 2017
Instructions to use the serial port of your Armadeus board to transfer files from/to your PC.
 |
Note: This page explains how to transfer files on the board when the Linux system has started, not from U-Boot !.
To know how to configure serial link for U-Boot communication, it's here. |
Contents
Introduction
When you only have a serial link (RS232/USB) as connection with your devt PC (ie no Ethernet available), then you can use Zmodem protocol to send/receive files to/from your Shell/Console of your Armadeus board.
Installation
Target (APF)
Modify your Buildroot configuration:
$ make menuconfig
to add lrzsz package:
Package Selection for the target --->
Networking applications --->
[*] lrzsz
and then rebuild your rootfs:
$ make
Reflash it or manually copy rz and sz executables found in $ARMADEUS_ROOTFS_DIR/usr/bin/.
Host
- Install lrzsz package, if not already installed on your system. For example on Ubuntu/Debian:
$ sudo apt-get install lrzsz
- Install minicom tool:
$ sudo apt-get install minicom
- The first time, configure minicom (as root):
$ sudo minicom -s
Usage
 |
Warning: You must use minicom as serial terminal and not kermit, sorry ! :-( |
- Be sure to have correctly configured Minicom (line speed, 8N1, no flow control, and correct download/upload directories path).
- Use rz for receiving and sz to send files:
Host (PC) --> Target (APF)
# cd /whereToPutTheFileOnTheTarget/ # rz -bZ .. waiting to receive.
- then in minicom do: Ctrl+A , s and choose zmodem protocol and the file to send.
- Wait a little and your file will be copied to your board rootfs ! ;-)
Target (APF) --> Host (PC)
# cd /location/of_the/file_to_send/on_the_apf/ # sz -b --zmodem filename
Minicom handles the file receiving automatically (and put it in your $HOME by default, or the directory you configured in Minicom: Ctrl+z, o, Filenames and paths, Download directory)
TBDL
Serial transfer through USB gadget as serial link
After having booted your board:
- On your Target, open a new terminal on your serial link (here USB):
# /sbin/getty -L ttygserial 115200 vt100
- On your Host, launch Minicom and configure it to use /dev/ttyUSB1 at 115200, then connect it to this terminal
Transfer without terminal
- On your Target, launch receiving:
# rz --zmodem 1>/dev/ttyXXX 0</dev/ttyXXX
- On your Host, launch transfer:
$ sz --zmodem /tftpboot/afiletosend 1>/dev/ttyUSB1 0</dev/ttyUSB1
