Difference between revisions of "USB to Ethernet adapter"

From ArmadeusWiki
Jump to: navigation, search
(LAN JP208 (ASIX AX88772C))
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
 +
[[Category:Network]]
 +
[[Category:USB]]
 +
 +
 
How-to use USB to Ethernet adapters
 
How-to use USB to Ethernet adapters
  
Line 19: Line 23:
 
[  +0,000001] usb 1-3.1.4: SerialNumber: 00000A
 
[  +0,000001] usb 1-3.1.4: SerialNumber: 00000A
 
</pre>
 
</pre>
 +
 
==== Kernel configuration ====
 
==== Kernel configuration ====
 
The driver is included in linux menuconfig.
 
The driver is included in linux menuconfig.
Line 38: Line 43:
 
==== Usage ====
 
==== Usage ====
  
Usage are the same has SMSC described below, except that:
+
Usage are the same as SMSC described below, except that:
 
* interface is named ethx (If you already mount the base ethernet, this adapter will be named eth1).
 
* interface is named ethx (If you already mount the base ethernet, this adapter will be named eth1).
 
* The Linux configuration given here avoid modprobe.
 
* The Linux configuration given here avoid modprobe.
Line 97: Line 102:
 
</pre>
 
</pre>
 
Additional informations concerning the EEPROM containt can be found on the SMSC web site.
 
Additional informations concerning the EEPROM containt can be found on the SMSC web site.
 
 
[[Category:Network]]
 
[[Category:USB]]
 

Latest revision as of 09:49, 30 April 2020


How-to use USB to Ethernet adapters

Prerequesities

Tested hardware

LAN JP208 (ASIX AX88772C)

LAN JP208 is a noname USB2 to Ethernet controller adapter.

Lan jp208.jpg

On host x86 computer, this converter is identified as an ASIX 8877 chip :

[  +0,112941] usb 1-3.1.4: New USB device found, idVendor=0b95, idProduct=772b
[  +0,000003] usb 1-3.1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  +0,000002] usb 1-3.1.4: Product: AX88772C
[  +0,000002] usb 1-3.1.4: Manufacturer: ASIX Elec. Corp.
[  +0,000001] usb 1-3.1.4: SerialNumber: 00000A

Kernel configuration

The driver is included in linux menuconfig.

$ make linux-menuconfig
 Device Drivers  --->
    [*] Network device support  --->
        USB Network Adapters  --->
            [...]
            <*>   Multi-purpose USB Networking Framework
            <*>     ASIX AX88xxx Based USB 2.0 Ethernet Adapters
            [...]

Usage

Usage are the same as SMSC described below, except that:

  • interface is named ethx (If you already mount the base ethernet, this adapter will be named eth1).
  • The Linux configuration given here avoid modprobe.

SMSC LAN9500

The SMSC LAN9500 is a Hi-Speed USB 2.0 to 10/100 Ethernet Controller. The datasheet can be found here: http://www.smsc.com/media/Downloads_Public/Data_Sheets/9500.pdf. An external EEPROM is used to store the LAN9500 configuration.


Kernel configuration

$ make linux-menuconfig
 Device Drivers  --->
    [*] Network device support  --->
        USB Network Adapters  --->
            [...]
            <M> Multi-purpose USB Networking Framework
            [...]
            <M> CDC Ethernet support
            [...]
            <M> SMSC LAN95XX based USB 2.0 10/100 ethernet devices

Additional tools

In order to read/write the configuration eeprom of the LAN9500, Ethtool has to be used.

$ make menuconfig
Target packages  --->
    Networking applications  --->
            [*] ethtool
            [*]   enable pretty printing
             

Usage

First mount the module:

# modprobe smsc95xx

then start the new ethernet port

# ifconfig usb0 192.168.10.208 up

If the message "No EEPROM present" is displayed, this indicates that no configuration file has been detected in the EEPROM. The LAN9500 will start in a default mode and the MAC address will be randomly generated by Linux. The EEPROM can be read/write by using ethtool once the module loaded

 ethtool -e usb0   # (eeprom read)
 ethtool -E usb0 magic 0x9500 offset xxx value xxx  # (eeprom write value at offset)

Additional informations concerning the EEPROM containt can be found on the SMSC web site.