Difference between revisions of "Vivado installation on Linux"
From ArmadeusWiki
(→Launch install) |
|||
| (7 intermediate revisions by 2 users not shown) | |||
| Line 4: | Line 4: | ||
== Introduction == | == Introduction == | ||
| − | Vivado is the new | + | Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new Xilinx's products. By default no Armadeus board has a new FPGA supported by Vivado, but, with the APF6, we can use Artix7 on a daughter board (or with Xilinx dev-kit), thanks to PCIe, and enjoy this new Xilinx tool. |
| − | This page is a tutorial to install Vivado on | + | This page is a tutorial on how to install Vivado on Debian Linux host computer. |
| − | {{Note| Vivado can't be used with | + | {{Note| Vivado can't be used with Spartan products, it starts with the "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...)}} |
== Installation == | == Installation == | ||
| + | |||
| + | === Requirements === | ||
| + | |||
| + | * unsure that Bash is the default shell: | ||
| + | <pre class="host"> | ||
| + | $ ls -al /bin/sh | ||
| + | lrwxrwxrwx 1 root root 4 févr. 10 14:49 /bin/sh -> bash | ||
| + | </pre> | ||
| + | * otherwise: | ||
| + | <pre class="host"> | ||
| + | $ sudo dpkg-reconfigure dash | ||
| + | </pre> | ||
=== Download === | === Download === | ||
| Line 27: | Line 39: | ||
* Fill forms then wait for about 20 minutes | * Fill forms then wait for about 20 minutes | ||
| + | |||
| + | == Launching Vivado == | ||
| + | |||
| + | * Go to the installed directory: | ||
| + | <pre class="host"> | ||
| + | $ cd /opt/Xilinx/Vivado/2014.4 | ||
| + | </pre> | ||
| + | |||
| + | * Source the architecture shell file: | ||
| + | <pre class="host"> | ||
| + | /opt/Xilinx/Vivado/2014.4$ source settings64.sh | ||
| + | </pre> | ||
| + | |||
| + | * Then launch it: | ||
| + | <pre class="host"> | ||
| + | /opt/Xilinx/Vivado/2014.4$ ./bin/vivado | ||
| + | </pre> | ||
== Links == | == Links == | ||
| + | |||
| + | * [http://forums.xilinx.com/t5/Installation-and-Licensing/Run-Vivado-2013-4-on-Debian/td-p/407359 Run Vivado 2013.4 on Debian] | ||
Revision as of 16:15, 11 February 2016
Contents
Introduction
Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new Xilinx's products. By default no Armadeus board has a new FPGA supported by Vivado, but, with the APF6, we can use Artix7 on a daughter board (or with Xilinx dev-kit), thanks to PCIe, and enjoy this new Xilinx tool. This page is a tutorial on how to install Vivado on Debian Linux host computer.
 |
Note: Vivado can't be used with Spartan products, it starts with the "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...) |
Installation
Requirements
- unsure that Bash is the default shell:
$ ls -al /bin/sh lrwxrwxrwx 1 root root 4 févr. 10 14:49 /bin/sh -> bash
- otherwise:
$ sudo dpkg-reconfigure dash
Download
- Download the file on xilinx website, note that you will need an account (free) to do that.
Xilinx_Vivado_SDK_2014.4_1119_1_Lin64.bin
Launch install
- To launch install simply type :
$ chmod 777 Xilinx_Vivado_SDK_2014.4_1119_1_Lin64.bin $ ./Xilinx_Vivado_SDK_2014.4_1119_1_Lin64.bin
- Fill forms then wait for about 20 minutes
Launching Vivado
- Go to the installed directory:
$ cd /opt/Xilinx/Vivado/2014.4
- Source the architecture shell file:
/opt/Xilinx/Vivado/2014.4$ source settings64.sh
- Then launch it:
/opt/Xilinx/Vivado/2014.4$ ./bin/vivado
