Difference between revisions of "APF27 PPS"

From ArmadeusWiki
Jump to: navigation, search
m (Feature list)
(Move PPS specific part to PPS page)
Line 63: Line 63:
  
 
|}
 
|}
 +
 +
==WiFi usage==
 +
On PPS, WiFi/Libertas driver usage is a little bit different than on other platforms. Here are the things to know:
 +
 +
===Drivers setup===
 +
You have to install Libertas SDIO and MMC drivers as modules to make Wi2Wi chipset work correctly on PPS (done by default):
 +
<pre class="host">
 +
$ make linux26-menuconfig
 +
</pre>
 +
 +
<pre class="config">
 +
Device drivers  --->
 +
    [*] Network device support  --->
 +
        Wireless LAN  --->
 +
            [*] Wireless LAN (IEEE 802.11)
 +
            <M>  Marvell 8xxx Libertas WLAN driver support
 +
            < >    Marvell Livertas 8388 USB 802.11b/g cards
 +
            <M>    Marvell Libertas 8385 and 8686 SDIO 802.11b/g cards
 +
    <M> MMC/SD/SDIO card support  --->
 +
              *** MMC/SD/SDIO Card Drivers ***
 +
        <M>  MMC block device driver
 +
</pre>
 +
 +
===Initializing the connection===
 +
Before creating the WiFi connection, you must load the Libertas SDIO and the MMC modules:
 +
<pre class="host">
 +
# modprobe mxcmmc
 +
# modprobe libertas_sdio
 +
</pre>
 +
 +
Then all informations on [[Libertas_driver]] page apply.
 +
 +
===Disconnect from the WiFi===
 +
You have to unload the MMC driver along with the Libertas SDIO to disconnect from the WiFi:
 +
<pre class="host">
 +
modprobe -r mxcmmc
 +
modprobe -r libertas_sdio
 +
</pre>
 +
 +
===Reset Wi2Wi===
 +
To reset the chipset, you have to use the Wi2Wi RESET GPIO:
 +
<pre class="host">
 +
source /usr/bin/gpio_helpers.sh
 +
 +
gpio_mode PE11 1
 +
gpio_set_value PE11 0
 +
gpio_set_value PE11 1
 +
</pre>
  
 
==Feature list==
 
==Feature list==

Revision as of 19:41, 1 March 2011

Description

PPS is an Armadeus System's baseboard for the APF27 module. It can be used to implement and securize network applications such as routers and gateways.

Front side, you can see dual Ethernet, USB 2.0 Host & OTG, WiFi Antenna, extension connector footprint and power supply
Back side, with an APF27 module plugged-in

Resources

Software features

There are some network applications/features that are preselected in the PPS baseboard default configuration:

Note Note: You can also use the PPS test scripts located in /usr/local/pps/scripts on the system to test some software functionalities.


SSH terminal

The APF27 PPS filesystem is configured to enable SSH connection from a host computer. It allows you to access a system terminal through the default Ethernet port (the one aside USB Host connector).

  • The default connection informations are:
    • IP address: 192.168.0.10
    • Login: guest
    • Password: armadeus
  • Then you can connect to your system by running the following command on your host:
 $ ssh guest@192.168.0.10

Debug / Development interface

In order to gain access to the serial port of the APF27 (U-Boot & Linux console), a small adapter cable has to be done. A standard 2.54mm pin header connector (J5) allows accessing the TX and RX debug lines of the iMX27. The signals are compatible with a the RS232 standard so no level translator is required.

The pinout is described in the datasheet and summarized here:

  • pin 1 (square pad): not connected
  • pin 2: TX line (processor side)
  • pin 3: RX line (processor side)
  • pin 4: GND
J5 pin 1
DB9 connection like on APF27Dev (requires Null-Modem cable)
DB9 connection for direct USB<->Serial adapter usage

WiFi usage

On PPS, WiFi/Libertas driver usage is a little bit different than on other platforms. Here are the things to know:

Drivers setup

You have to install Libertas SDIO and MMC drivers as modules to make Wi2Wi chipset work correctly on PPS (done by default):

$ make linux26-menuconfig
Device drivers  --->
    [*] Network device support  --->
        Wireless LAN  --->
            [*] Wireless LAN (IEEE 802.11)
            <M>   Marvell 8xxx Libertas WLAN driver support
            < >     Marvell Livertas 8388 USB 802.11b/g cards
            <M>     Marvell Libertas 8385 and 8686 SDIO 802.11b/g cards
    <M> MMC/SD/SDIO card support  --->
              *** MMC/SD/SDIO Card Drivers ***
        <M>   MMC block device driver

Initializing the connection

Before creating the WiFi connection, you must load the Libertas SDIO and the MMC modules:

# modprobe mxcmmc
# modprobe libertas_sdio

Then all informations on Libertas_driver page apply.

Disconnect from the WiFi

You have to unload the MMC driver along with the Libertas SDIO to disconnect from the WiFi:

modprobe -r mxcmmc
modprobe -r libertas_sdio

Reset Wi2Wi

To reset the chipset, you have to use the Wi2Wi RESET GPIO:

source /usr/bin/gpio_helpers.sh

gpio_mode PE11 1
gpio_set_value PE11 0
gpio_set_value PE11 1

Feature list

Wired communication

Wireless communication

Other

FPGA