Difference between revisions of "WiFi"
m |
m |
||
Line 1: | Line 1: | ||
To see your wireless configuration you need wireless tools selected in buildroot: | To see your wireless configuration you need wireless tools selected in buildroot: | ||
− | < | + | <pre class=config> |
Package Selection for the target ---> | Package Selection for the target ---> | ||
[*] Networking ---> | [*] Networking ---> | ||
[*] wireless tools | [*] wireless tools | ||
− | </ | + | </pre> |
then you can use ''iwconfig'' command. | then you can use ''iwconfig'' command. | ||
Revision as of 11:05, 2 February 2009
To see your wireless configuration you need wireless tools selected in buildroot:
Package Selection for the target ---> [*] Networking ---> [*] wireless tools
then you can use iwconfig command.
# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=0 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0/100 Signal level:112/146 Noise level:0/0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
To configure WiFi cryptography, only WEP can be set as is. If you want to configure dongle for WPA, install [http://hostap.epitest.fi/wpa_supplicant/ wpa_supplicant].
WEP configuration
Note : to see all access point available for your apf, use iwlist command :
# iwlist scanning
This example is given for a WiFi Access Point named armadeus, but the key is false of course ;) :
# iwconfig wlan0 essid armadeus # iwconfig wlan0 key 12345678901234567890 # ifconfig wlan0 up firmware: requesting rt73.bin ADDRCONF(NETDEV_UP): wlan0: link is not ready # ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Now, the WiFi adapter is ready and attached :
# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"armadeus" Mode:Managed Frequency:2.437 GHz Access Point: 00:1B:2F:E7:E4:08 Bit Rate=2 Mb/s Tx-Power=7 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:XXXXXXXXXXXXXXXXXXXXXXXXXX Security mode:restricted Power Management:off Link Quality:0/100 Signal level:73/146 Noise level:0/0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
We can configure the network to access internet via the WiFi interface instead of the Ethernet one :
# ifconfig eth0 down # ifconfig wlan0 192.168.0.212 # route add default gw 192.168.0.1 dev wlan0
And configure the nameserver in /etc/resolv.conf
domain dev.null nameserver 192.168.0.207 ~ ~ ~
We can now ping the best website in the world :
# ping www.armadeus.org PING www.armadeus.org (213.186.33.5): 56 data bytes 64 bytes from 213.186.33.5: seq=0 ttl=122 time=66.735 ms 64 bytes from 213.186.33.5: seq=1 ttl=122 time=50.392 ms ^C --- www.armadeus.org ping statistics --- 2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 50.392/58.563/66.735 ms
Surf on the net
To surf on the web, you can use links software :
# links www.armadeus.org
It's an ASCII internet browser. For more informations about Links.