Difference between revisions of "Chimei LW700"
From ArmadeusWiki
(New page: {{Under_Construction}} This adaptor board allows you to connect a [http://document.sharpsma.com/files/LQ043T3DX02_SP_122805.pdf Sharp's LQ043 LCD] to your DevLight or DevFull.<br> The de...) |
|||
| Line 1: | Line 1: | ||
{{Under_Construction}} | {{Under_Construction}} | ||
| − | This adaptor board allows you to connect a [http:// | + | This adaptor board allows you to connect a [http://www.armadeus.com/english/products-peripherals-lw700at_adapt.html CHIMEY LW700AT LCD] to your DevFull.<br> |
| − | The description, the datasheet and the schematics of this adaptor board [http://www.armadeus.com/english/products-peripherals- | + | The description, the datasheet and the schematics of this adaptor board [http://www.armadeus.com/english/products-peripherals-lw700at_adapt.html can be found here.] |
| − | The following table summarizes the possibilities to connect the | + | The following table summarizes the possibilities to connect the LQW700AT and the Touchscreen to your development board: |
Revision as of 15:23, 17 December 2009
Page under construction...
Informations on this page are not guaranteed !!
This adaptor board allows you to connect a CHIMEY LW700AT LCD to your DevFull.
The description, the datasheet and the schematics of this adaptor board can be found here.
The following table summarizes the possibilities to connect the LQW700AT and the Touchscreen to your development board:
| APF27Dev | APF9328DevFull | APF9328DevLightV1 | APF9328DevLightV2 | |
|---|---|---|---|---|
| TFT usage | flat cable (1) connected between J10 of the APF27Dev and X5 of the LCD_Adapt | flat cable (1) connected between X12 of the DevFull and X5 of the LCD_Adapt | On the Devlight V1, the LCD port is not prerouted. This means that you have to solder several wire between the vias corresponding to the LCD signals and a free place on the board where you can add a 2x15pins header. Take a look at the Devlight datasheet. You will find a table representing the bottom side of the board. On the board (bottom), you will see a silkscreen indicating the names of each vias. In the LQ043_Adapt datasheet, you will find the pin description of the 2x15 pins connector. Connect (1 to 1) the signals of the LQ043_adapt to the ones of the Devlight.The flat cable (1) is although required | flat cable(1) connected between X5 of the LCD_Adapt and LCD connector of the DevLight |
| Touchscreen usage | 4 wires cable (2) connected between X2 of the LCD_Adapt and J14 of the APF27Dev | 4 wires cable (2) connected between X2 of the LCD_Adapt and X32 of the DevFull | For those who do not have the APF9328Devfull and would like to use a touch panel, a reserved space has been foreseen on the LQ043_adapt board to solder the TSC2102 (U3) and a small regulator (LM317/U4) . This avoids developping or buying a dedicated PCB.In that case one more connection is required:
| |
Contents
(1) Flat cable
A simple flat cable (PC like) can be used to connect the LQ043_Adapt to the APF27Dev/APF9328DevFull. If you do not have one, a ready to use cable can be found here.
Align the pins 1 (square via) on both boards together.
Do not use long cables.
(2) 4 wires cable
It is a simple one to one 4 wire cables (2.54mm single row headers on both boards: LQ043_adapt and Devfull)
