Difference between revisions of "FPGA loader"
From ArmadeusWiki
m (→Module compilation & installation) |
m (→Driver usage) |
||
| (30 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
| + | [[Category: FPGA]] | ||
| + | |||
On this page, you will find all the informations needed to use the Linux FPGA loader driver. | On this page, you will find all the informations needed to use the Linux FPGA loader driver. | ||
This driver allows you to load the FPGA of your APF board from Linux userspace/shell (ie FPGA reprogrammation after Linux boot). | This driver allows you to load the FPGA of your APF board from Linux userspace/shell (ie FPGA reprogrammation after Linux boot). | ||
| − | == | + | == Driver installation== |
| − | + | Driver is installed in default Armadeus rootfs. | |
| − | + | ||
| − | + | For the hackers, code is located in ''target/linux/modules/fpga/dev_tools/fpga_devtools/''. | |
| − | + | ||
| − | + | ||
| − | + | == Driver usage == | |
| − | + | *To upload a new firmware, use the small helper script that can do all the job for you (load driver and then firmware). Just call it with the bitfile (.rbf for APF6SP and .bin for the other boards) as parameter. For example: | |
| + | <pre class="apf"> | ||
| + | # load_fpga bramtest_top_apf.bin | ||
| + | </pre> | ||
| − | + | * For APF6_SP a periph.rbf must be [[Target_Software_Installation#APF6_SP | loaded in U-Boot]] before, the core.rbf can then be loaded under linux with load_fpga: | |
| − | # | + | <pre class="apf"> |
| − | + | # load_fpga firmware.core.rbf | |
| + | </pre> | ||
| + | * [[Simple_blinking_LED | You can find some ready to use bitfiles in ''firmware/leds/blinking_led/bin/'' (blinking LED).]] | ||
| − | + | {{Note| On '''APF6_SP''' the command load_fpga work only throught PCIe, see [[PCIe fpga load]] to know how it works}} | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | == | + | ==Troubleshots== |
| − | * | + | === APF51 === |
| − | + | * Use binary format '''.bin''', bitstream format '''.bit''' doesn't work. | |
| − | + | ||
| − | + | All the troubleshots are handled by the ''/usr/bin/load_fpga'' utility, mentionned above. | |
| − | + | ||
| − | + | [[Category:FPGA]] | |
| − | + | ||
Latest revision as of 08:41, 27 August 2015
On this page, you will find all the informations needed to use the Linux FPGA loader driver.
This driver allows you to load the FPGA of your APF board from Linux userspace/shell (ie FPGA reprogrammation after Linux boot).
Driver installation
Driver is installed in default Armadeus rootfs.
For the hackers, code is located in target/linux/modules/fpga/dev_tools/fpga_devtools/.
Driver usage
- To upload a new firmware, use the small helper script that can do all the job for you (load driver and then firmware). Just call it with the bitfile (.rbf for APF6SP and .bin for the other boards) as parameter. For example:
# load_fpga bramtest_top_apf.bin
- For APF6_SP a periph.rbf must be loaded in U-Boot before, the core.rbf can then be loaded under linux with load_fpga:
# load_fpga firmware.core.rbf
 |
Note: On APF6_SP the command load_fpga work only throught PCIe, see PCIe fpga load to know how it works |
Troubleshots
APF51
- Use binary format .bin, bitstream format .bit doesn't work.
All the troubleshots are handled by the /usr/bin/load_fpga utility, mentionned above.
