Quartus installation on Linux
Introduction
Quartus web edition 14.0 is the software used to synthesize bitstream for Altera FPGAs. It's required for the cyclone V soldered on APF6SP.
Installation guide for version 14.0
Package needed
On debian jessie :
sudo apt-get install libstdc++5 libmotif4 libxp6 libcurl3 # for 64 arch, install also 32bits packets: sudo dpkg --add-architecture i386 sudo apt-get install libstdc++5:i386 libmotif4:i386 libxp6:i386 libcurl3:i386
Download
Download the big (4GB) quartus installer here (Use "download software web edition" button).
Uncompress and install
- Untar the archive :
tar -xvf Quartus-web-14.0.0.200-linux.tar
- run the installer:
bash setup.sh
- follow the instructions to install it where you want.
configure .bashrc
Adding the path of your quartus in ~/.bashrc
export ALTERAPATH="/opt/quartus/altera/14.0/"
export ALTERAOCLSDKROOT="${ALTERAPATH}/hld"
export QUARTUS_ROOTDIR=${ALTERAPATH}/quartus
export QUARTUS_ROOTDIR_OVERRIDE="$QUARTUS_ROOTDIR"
export PATH=$PATH:${ALTERAPATH}/quartus/bin
export PATH=$PATH:${ALTERAPATH}/nios2eds/bin
export PATH=$PATH:${QSYS_ROOTDIR}Launch Quartus
To launch quartus, open a terminal and simply type :
$ quartus
USB-Blaster
USB-BLaster is an USB JTAG adaptor usefull to debug altera FPGA. Under Linux some rights must be added to use it with quartus.
- create an udev rules files in :
/etc/udev/rules.d/altera-usb-blaster.rules
- And add following configuration :
ATTR{idVendor}=="09fb", ATTR{idProduct}=="6001", MODE="666"
Version 15.1 prime lite
 |
Note: Quartus 15.1.1 with update 1 take about ~16GB once installed, but ~15 more GB are required for download/untar before installation |
Version 15.1 with update (click on updates tab).
- In Complete Download chapter, download the big archive with update 1 (7.6GB) on the download center (free Altera account needed):
Quartus-lite-15.1.1.189-linux.tar
- Watch a good movie (min 2 hours)
- Move the big archive in a directory with enough free space and untar it:
$ tar -xvf Quartus-lite-15.1.1.189-linux.tar
- Take a little coffee (~3 min)
- Launch the installation:
./setup.sh
- follow the instructions to install it where you want
- Take a big coffee or go to lunch (~30min)
- Change your environment variables in your .bashrc:
export ALTERAPATH="/directory/where/you/installed/quartus/"
export ALTERAOCLSDKROOT="${ALTERAPATH}/hld"
export QUARTUS_ROOTDIR=${ALTERAPATH}/quartus
export QUARTUS_ROOTDIR_OVERRIDE="$QUARTUS_ROOTDIR"
export QSYS_ROOTDIR="${ALTERAPATH}/quartus/sopc_builder/bin"
export PATH=$PATH:${ALTERAPATH}/quartus/bin
export PATH=$PATH:${ALTERAPATH}/nios2eds/bin |
Warning: The altera installation script will edit your .bashrc file adding a line at the end.export QUARTUS_ROOTDIR=... |
- Run quartus in a new console and select prime software:
$ quartus
Version 19.1 prime lite
Installation process is mainly identical with this little fixes.
Perl Getopt::Long
When synthesize platform design (qsys) a perl error like this occure:
... Can't locate Getopt/Long.pm in @INC ...
Apparently, the module is not installed for Intel embedded perl. To solve the problem, a solution is to use your perl installed in distribution.
But before, be sure that you have the getopt installed correctly :
$ sudo apt install libgetopt-simple-perl
Then go to your Intel Quartus installation :
$ cd altera/19.1/quartus/linux64/perl/bin $ mv perl perl_old $ ln -s /usr/bin/perl
And relaunch your quartus project.
