Difference between revisions of "U-Boot-2011.12"
From ArmadeusWiki
m (→TODO list) |
|||
(43 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
+ | ==Status== | ||
− | + | * Please check [[U-Boot-2012.04]] that is now the default U-Boot version for all the APF boards | |
− | + | ||
− | * | + | |
− | [[ | + | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
==Features/Status== | ==Features/Status== | ||
Line 36: | Line 30: | ||
| || || || || || | | || || || || || | ||
|---------------- | |---------------- | ||
− | |'''U-Boot power on''' || style="background:#00ff00;" | U-Boot 2011.12...<br />I2C: ready<br />DRAM: 16 MiB<br />Flash: 8 MiB<br />In: serial<br />Out: serial<br />Err: serial<br />Net: dm9000 || style="background:# | + | |'''U-Boot power on''' || style="background:#00ff00;" | U-Boot 2011.12...<br />I2C: ready<br />DRAM: 16 MiB<br />Flash: 8 MiB<br />In: serial<br />Out: serial<br />Err: serial<br />Net: dm9000 || style="background:#00ff00;" | U-Boot 2011.12... <br />Freescale i.MX28 family<br />DRAM: 128 MiB<br />NAND: 256 MiB<br />MMC: MXS MMC: 0<br />In: serial<br />Out: serial<br />Err: serial<br />Net: FEC0 || style="background:#00ff00;" | U-Boot 2011.12..<br />CPU: Freescale i.MX27 at 399 MHz<br />Armadeus APF27<br />DRAM: 64 MiB<br />NAND: 256 MiB || style="background:#00ff00;" | U-Boot 2011.12...<br />I2C: ready<br />DRAM: 256-512 MiB<br />NAND: 512 MiB<br />In: serial<br />Out: serial<br />Err: serial<br />Net: FEC |
+ | || power on the board and check the boot log of the board | ||
+ | |---------------- | ||
+ | |'''NOR/NAND flash''' || style="background:#00ff00;" | 8 MiB|| style="background:#00ff00;" | 256MiB-2GiB || style="background:#00ff00;" | 256MiB-2GiB || style="background:#00ff00;" | 512MiB-4GiB || startup sceen shall display:<br />Flash: xx MiB | ||
|---------------- | |---------------- | ||
− | |''' | + | |'''RAM''' || style="background:#00ff00;" | 16/32 MiB|| style="background:#00ff00;" | 128MiB-512MiB|| style="background:#00ff00;" | 64-256MiB || style="background:#00ff00;" | 256-512MiB || startup sceen shall display:<br />DRAM: 16 MiB |
|---------------- | |---------------- | ||
− | |''' | + | |'''Ethernet driver''' || style="background:#00ff00;" | dm9000|| style="background:#00ff00;" | FEC0 || style="background:#00ff00;" | FEC || style="background:#00ff00;" | FEC || startup sceen shall display:<br />Net: <DRIVER> |
|---------------- | |---------------- | ||
− | |'''Ethernet | + | |'''Ethernet MAC''' || style="background:#00ff00;" | dm9000 read<br />00000000: 1e00 00ac|| style="background:#00ff00;" | bdinfo<br />...<br />ethaddr = 00:1e:ac:... || style="background:#00ff00;" | imxfuse mac<br />iMX mac_addr in fuse: 00:1e:ac:... || style="background:#00ff00;" | iim read fecmac<br />FEC MAC address: 0x00:0x1e:0xac:...|| test the presence of the MAC address in EEPROM/fuses <br /> the command bdinfo should return a valid mac address |
|---------------- | |---------------- | ||
− | |''' | + | |'''Default IP''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || the default IP variables should be:<br /> ipaddr=192.168.0.10<br /> netmask=255.255.255.0<br /> serverip=192.168.0.2<br /> gatewayip=192.168.0.1<br /> use the "flash_reset_env" script<br />to restore the default environment variables |
|---------------- | |---------------- | ||
− | |''' | + | |'''DHCP''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || the command "DHCP" should be able<br />to update IP environment variables according<br /> to your network and DHCP server |
|---------------- | |---------------- | ||
− | |''' | + | |'''Ping''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || set ipaddr & serverip according to your network.<br />Test the connection to the server: <br />ping ${serverip} should return the status "alive" |
|---------------- | |---------------- | ||
− | |''' | + | |'''Board reset''' ||style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || command "reset" shall reset the board |
|---------------- | |---------------- | ||
− | |''' | + | |'''TFTP''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || the command "run download_uboot" should <br />UBoot from the host PC into the target RAM |
|---------------- | |---------------- | ||
− | |''' | + | |'''NFS''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || the command <br />"nfs ${loadaddr} ${serverip}:/tftpboot/${board_name}-linux.bin" should download<br />linux kernel from the host PC into the target RAM |
|---------------- | |---------------- | ||
− | |''' | + | |'''Board upgrade scripts''' ||style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || use the hereafter scripts to update the software of the board:<br /> run update_all<br />run flash_reset_env |
|---------------- | |---------------- | ||
− | |''' | + | |'''I2C''' || style="background:#00ff00;" | 38 76 7F || postponed || postponed || not supported : unreliable - device detected randomly || startup sceen shall display:<br />I2C: ready<br />the command "i2c probe" should return the list<br />of devices on the i2c bus of the board |
|---------------- | |---------------- | ||
− | |''' | + | |'''linux boot from flash''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || the command "boot" should start linux and rootfs from flash<br />the linux login should be "armadeus login: " |
|---------------- | |---------------- | ||
− | |''' | + | |'''NFS boot (rootfs)''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || http://www.armadeus.com/wiki/index.php?title=Nfs#Boot_from_NFS <br /> the command "run nfsboot" should start linux using <br />rootfs over a NFS shared drive on <br />your host server ${serverip} |
|---------------- | |---------------- | ||
− | |''' | + | |''' rootfs on SD/MMC''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || http://www.armadeus.com/wiki/index.php?title=MultiMediaCard#Booting_from_MMC.2FSD <br /> the command "run mmcboot" should start linux using <br />a rootfs on your sd/mmc memory card |
|---------------- | |---------------- | ||
− | |''' | + | |'''Flash lock/unlock''' || style="background:#00ff00;" | || Not Applicable || style="background:#00ff00;" | || style="background:#00ff00;" | || For APF9328: <br />protect on all<br />erase ${env_addr} +${env_len} <br />-> - Warning: 1 protected sectors will not be erased!<br />protect off all<br />erase ${env_addr} +${env_len} <br />-> no warning - erase done<br /> other apf boards:<br />nand lock; nand erase.part kernel<br />Should not erase the kernel partion<br />(error message, system hang or no message)<br /> |
+ | boot linux<br />to confirm nand integrity -> kernel should start | ||
|---------------- | |---------------- | ||
− | |''' | + | |'''Env compatibility change''' || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || style="background:#00ff00;" | || force a new environment version and check <br />the warning on next reboot:<br />setenv env_version 0<br />saveenv<br />reset<br />=> *** Warning - Environment version change suggests:<br />run flash_reset_env; reset |
|---------------- | |---------------- | ||
− | |''' | + | |'''FPGA control''' || style="background:#00ff00;" | blinking_led_<br />apf9328_200k.bit || Not Applicable || style="background:#00ff00;" | blinking_led_<br />apf27_200k.bit || style="background:#00ff00;" | blinking_led_<br />apf51_lx9.bin || the command "fpga info 0" should indicate<br /> the presence of the spartan 3 <br />Test FPGA download with the blinking_led bit file of your board:<br />tftpboot ${loadaddr} blinking_led_apfxxxx_xxxk.bit<br />fpga load 0 ${loadaddr} ${filesize}<br /> should make the LED blinking without error |
|---------------- | |---------------- | ||
− | |''' | + | |'''Firmware autoload''' || style="background:#00ff00;" | || Not Applicable|| style="background:#00ff00;" | || style="background:#00ff00;" | || run flash_firmware<br />setenv firmware_autoload 1<br />saveenv<br /><power off>/<power on> the board<br />LED should blink after a couple of seconds and<br />UBoot should continue countdown to boot linux |
|---------------- | |---------------- | ||
− | |''' | + | |'''imxfuse commands''' || Not Applicable || style="background:#00ffff;" | ocotp || style="background:#ffff00;" | imxfuse mac... || style="background:#00ff00;" | iim blow fecmac... || Use production tool to blow a MAC address |
|---------------- | |---------------- | ||
− | |''' | + | |'''Detect RAM SIze''' || Not Applicable || style="background:#00ff00;" | 128MiB || not supported || style="background:#00ff00;" | Board rev 1 with 512MiB || Using the default UBoot config test the given<br /> config is correct during boot |
|---------------- | |---------------- | ||
− | |'''PAR cleared''' || style="background:# | + | |'''PAR cleared''' || style="background:#00ff00;" | || Not Applicable || style="background:#00ff00;" | || Not Applicable || run unlock_regs; boot<br />once logged on linux try the command<br />imxregs<br />should display imx register value instead of any error like "Unhandled fault" |
|---------------- | |---------------- | ||
− | |'''NETCONSOLE''' || | + | |'''NETCONSOLE''' || not supported || not supported || not supported || not supported || [[Ethernet_console]] |
|---------------- | |---------------- | ||
| '''LCD''' || not supported || not supported || not supported || not supported || | | '''LCD''' || not supported || not supported || not supported || not supported || |
Latest revision as of 23:50, 18 June 2012
Status
- Please check U-Boot-2012.04 that is now the default U-Boot version for all the APF boards
Features/Status
Status | Legend Color |
Test passed | |
Compilation or runtime test failed | |
To be tested | |
Optional/not activated by default | |
NA/not supported |
Feature | Status | Test case | |||
---|---|---|---|---|---|
boards | apf9328 | apf28 | apf27 | apf51 | |
U-Boot power on | U-Boot 2011.12... I2C: ready DRAM: 16 MiB Flash: 8 MiB In: serial Out: serial Err: serial Net: dm9000 |
U-Boot 2011.12... Freescale i.MX28 family DRAM: 128 MiB NAND: 256 MiB MMC: MXS MMC: 0 In: serial Out: serial Err: serial Net: FEC0 |
U-Boot 2011.12.. CPU: Freescale i.MX27 at 399 MHz Armadeus APF27 DRAM: 64 MiB NAND: 256 MiB |
U-Boot 2011.12... I2C: ready DRAM: 256-512 MiB NAND: 512 MiB In: serial Out: serial Err: serial Net: FEC |
power on the board and check the boot log of the board |
NOR/NAND flash | 8 MiB | 256MiB-2GiB | 256MiB-2GiB | 512MiB-4GiB | startup sceen shall display: Flash: xx MiB |
RAM | 16/32 MiB | 128MiB-512MiB | 64-256MiB | 256-512MiB | startup sceen shall display: DRAM: 16 MiB |
Ethernet driver | dm9000 | FEC0 | FEC | FEC | startup sceen shall display: Net: <DRIVER> |
Ethernet MAC | dm9000 read 00000000: 1e00 00ac |
bdinfo ... ethaddr = 00:1e:ac:... |
imxfuse mac iMX mac_addr in fuse: 00:1e:ac:... |
iim read fecmac FEC MAC address: 0x00:0x1e:0xac:... |
test the presence of the MAC address in EEPROM/fuses the command bdinfo should return a valid mac address |
Default IP | the default IP variables should be: ipaddr=192.168.0.10 netmask=255.255.255.0 serverip=192.168.0.2 gatewayip=192.168.0.1 use the "flash_reset_env" script to restore the default environment variables | ||||
DHCP | the command "DHCP" should be able to update IP environment variables according to your network and DHCP server | ||||
Ping | set ipaddr & serverip according to your network. Test the connection to the server: ping ${serverip} should return the status "alive" | ||||
Board reset | command "reset" shall reset the board | ||||
TFTP | the command "run download_uboot" should UBoot from the host PC into the target RAM | ||||
NFS | the command "nfs ${loadaddr} ${serverip}:/tftpboot/${board_name}-linux.bin" should download linux kernel from the host PC into the target RAM | ||||
Board upgrade scripts | use the hereafter scripts to update the software of the board: run update_all run flash_reset_env | ||||
I2C | 38 76 7F | postponed | postponed | not supported : unreliable - device detected randomly | startup sceen shall display: I2C: ready the command "i2c probe" should return the list of devices on the i2c bus of the board |
linux boot from flash | the command "boot" should start linux and rootfs from flash the linux login should be "armadeus login: " | ||||
NFS boot (rootfs) | http://www.armadeus.com/wiki/index.php?title=Nfs#Boot_from_NFS the command "run nfsboot" should start linux using rootfs over a NFS shared drive on your host server ${serverip} | ||||
rootfs on SD/MMC | http://www.armadeus.com/wiki/index.php?title=MultiMediaCard#Booting_from_MMC.2FSD the command "run mmcboot" should start linux using a rootfs on your sd/mmc memory card | ||||
Flash lock/unlock | Not Applicable | For APF9328: protect on all erase ${env_addr} +${env_len} -> - Warning: 1 protected sectors will not be erased! protect off all erase ${env_addr} +${env_len} -> no warning - erase done other apf boards: nand lock; nand erase.part kernel Should not erase the kernel partion (error message, system hang or no message) boot linux | |||
Env compatibility change | force a new environment version and check the warning on next reboot: setenv env_version 0 saveenv reset => *** Warning - Environment version change suggests: run flash_reset_env; reset | ||||
FPGA control | blinking_led_ apf9328_200k.bit |
Not Applicable | blinking_led_ apf27_200k.bit |
blinking_led_ apf51_lx9.bin |
the command "fpga info 0" should indicate the presence of the spartan 3 Test FPGA download with the blinking_led bit file of your board: tftpboot ${loadaddr} blinking_led_apfxxxx_xxxk.bit fpga load 0 ${loadaddr} ${filesize} should make the LED blinking without error |
Firmware autoload | Not Applicable | run flash_firmware setenv firmware_autoload 1 saveenv <power off>/<power on> the board LED should blink after a couple of seconds and UBoot should continue countdown to boot linux | |||
imxfuse commands | Not Applicable | ocotp | imxfuse mac... | iim blow fecmac... | Use production tool to blow a MAC address |
Detect RAM SIze | Not Applicable | 128MiB | not supported | Board rev 1 with 512MiB | Using the default UBoot config test the given config is correct during boot |
PAR cleared | Not Applicable | Not Applicable | run unlock_regs; boot once logged on linux try the command imxregs should display imx register value instead of any error like "Unhandled fault" | ||
NETCONSOLE | not supported | not supported | not supported | not supported | Ethernet_console |
LCD | not supported | not supported | not supported | not supported | |
SPI | not supported | not supported | not supported | not supported | |
USB | not supported | not supported | not supported | not supported |