Difference between revisions of "TSC2102 Linux driver"

From ArmadeusWiki
Jump to: navigation, search
m (Usage)
m (Envt variables)
Line 48: Line 48:
 
  export TSLIB_CONFFILE=/etc/ts.conf
 
  export TSLIB_CONFFILE=/etc/ts.conf
 
  export TSLIB_CALIBFILE=/etc/pointercal
 
  export TSLIB_CALIBFILE=/etc/pointercal
 +
* you can add them to your ''.bashrc'':
 +
# cd
 +
# vi .bashrc
  
 
===Device file creation if not exist===  
 
===Device file creation if not exist===  

Revision as of 21:58, 2 May 2008

Driver Installation

$ make linux-menuconfig
in Device Drivers  ---> Input device support  ---> select <*>   Event interface  as builtin
in Device Drivers  ---> Input device support  ---> [*]   Touchscreens  ---> select <M>   TSC 2102 based touchscreens as module

in Device Drivers  ---> SPI support  --->  select <M> Freescale iMX SPI controller as module
in Device Drivers  ---> SPI support  ---> --- TSC2102 codec support should be selected

in Device Drivers  ---> select <M> Hardware Monitoring support  ---> as module
$ make linux

Then reflash your Linux kernel and your Rootfs...

Architecture

Touchscreen (tsc2102_ts.ko) HWmon ALSA
TSC2102 Main driver (tsc2102.ko)
Linux API

Usage

  • load all the needed drivers:
# insmod /lib/modules/drivers/hwmon/hwmon.ko
# insmod /lib/modules/drivers/spi/spi_imx.ko
# insmod /lib/modules/drivers/spi/tsc2102.ko
# insmod /lib/modules/drivers/input/touchscreen/tsc2102_ts.ko
# insmod /lib/modules/2.6.23.1/kernel/drivers/input/evdev.ko

Then:

  • get temperature and voltage with hwmon (Hardware Monitoring) interface
cat /sys/class/hwmon/hwmon0/device/temp1_input   -- result in m°C

TSLib API Installation

Install the Tslib touchscreen API

Envt variables

  • You should define some ENVT variables to use the touchscreen API (tslib):
export TSLIB_TSDEVICE=/dev/input/event0
export TSLIB_TSEVENTTYPE=INPUT
export TSLIB_CONFFILE=/etc/ts.conf
export TSLIB_CALIBFILE=/etc/pointercal
  • you can add them to your .bashrc:
# cd
# vi .bashrc

Device file creation if not exist

  • /dev/input/event0 is created from the infos got from:
# cat /sys/class/input/event0/dev
13:64
# mkdir /dev/input
# cd /dev/input/
# mknod event0 c 13 64
# ls -al
drwxr-xr-x    2 root     root            0 Jan  1 00:39 .
drwxr-xr-x    5 root     root            0 Jan  1 00:39 ..
crw-r--r--    1 root     root      13,  64 Jan  1 00:39 event0
#

Quick test

To quickly check driver fonctionnality, touch the screen and check that tsc2102 interrupts count is increasing:

# cat /proc/interrupts
          CPU0
26:          0         MPU  IMX-uart
29:         17         MPU  IMX-uart
30:         22         MPU  IMX-uart
35:         12         MPU  imx-mmc
39:         14         MPU  I2C_IMX
40:         16         MPU  imx-spi.2
41:          0         MPU  imx-spi.1
59:       3682         MPU  i.MX Timer Tick
60:          0         MPU  DMA
61:          0         MPU  DMA
110:         0        GPIO  eth0
168:         0        GPIO  tsc2102
Err:         0
#

or start the touchscreen calibration tool:

/usr/bin/ts_calibrate

Links