Difference between revisions of "USB Gadget"
From ArmadeusWiki
m (→To emulate a mass storage device:) |
(moved installation) |
||
Line 3: | Line 3: | ||
==Introduction== | ==Introduction== | ||
− | You can connect your | + | You can connect your APF9328 board to your PC using its USB Device port and it can be "enumerated" as most common USB devices (depending on the type of communication you want to use): |
* serial device | * serial device | ||
* net device | * net device | ||
Line 10: | Line 10: | ||
==Installation== | ==Installation== | ||
− | * | + | * The drivers are now installed by default (since armadeus-3.0) |
− | + | * you should have following modules in your kernel source tree: | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | * | + | |
− | + | ||
− | + | ||
'''drivers/usb/gadget/gadgetfs.ko''' For test | '''drivers/usb/gadget/gadgetfs.ko''' For test | ||
'''drivers/usb/gadget/g_ether.ko''' Ethernet emulation on USB | '''drivers/usb/gadget/g_ether.ko''' Ethernet emulation on USB | ||
Line 24: | Line 17: | ||
'''drivers/usb/gadget/g_serial.ko''' Serial emulation on USB | '''drivers/usb/gadget/g_serial.ko''' Serial emulation on USB | ||
'''drivers/usb/gadget/g_zero.ko''' For test | '''drivers/usb/gadget/g_zero.ko''' For test | ||
− | |||
− | |||
− | |||
==Usage== | ==Usage== | ||
− | |||
− | |||
− | |||
− | |||
===To emulate a mass storage device:=== | ===To emulate a mass storage device:=== | ||
− | * [[USB_Gadget#Links |create]] or get a "backing storage file" ([http://dl.free.fr/ | + | * [[USB_Gadget#Links |create]] or get a "backing storage file" ([http://dl.free.fr/q9IKqqweK for example]) |
* copy this file (uncompressed) in the '''/tmp''' directory of your board (here my Host PC has 192.168.0.20 as IP @): | * copy this file (uncompressed) in the '''/tmp''' directory of your board (here my Host PC has 192.168.0.20 as IP @): | ||
# tftp -g -r backing_file.gz -l /tmp/backing_file.gz 192.168.0.20 | # tftp -g -r backing_file.gz -l /tmp/backing_file.gz 192.168.0.20 |
Revision as of 16:26, 18 May 2009
Instructions to use the USB port of your Armadeus board to communicate with your PC
Contents
Introduction
You can connect your APF9328 board to your PC using its USB Device port and it can be "enumerated" as most common USB devices (depending on the type of communication you want to use):
- serial device
- net device
- mass storage device
Installation
- The drivers are now installed by default (since armadeus-3.0)
- you should have following modules in your kernel source tree:
drivers/usb/gadget/gadgetfs.ko For test drivers/usb/gadget/g_ether.ko Ethernet emulation on USB drivers/usb/gadget/g_file_storage.ko Mass storage drivers/usb/gadget/g_serial.ko Serial emulation on USB drivers/usb/gadget/g_zero.ko For test
Usage
To emulate a mass storage device:
- create or get a "backing storage file" (for example)
- copy this file (uncompressed) in the /tmp directory of your board (here my Host PC has 192.168.0.20 as IP @):
# tftp -g -r backing_file.gz -l /tmp/backing_file.gz 192.168.0.20 # gunzip /tmp/backing_file.gz
- load g_file_storage module:
# modprobe g_file_storage file=/tmp/backing_file g_file_storage gadget: File-backed Storage Gadget, version: 28 November 2005 g_file_storage gadget: Number of LUNs=1 g_file_storage gadget-lun0: ro=0, file: /tmp/backing_file
- connect target's USB cable to your PC and,
On your Linux Host:
- If you have a recent Linux distribution, your device should be automatically mounted. Otherwise:
- as root, launch dmesg and find the /dev/sdaX device assigned to your board:
... usb 1-1.4: new full speed USB device using uhci_hcd and address 7 ... usb 1-1.4: configuration #1 chosen from 1 choice ... scsi1 : SCSI emulation for USB Mass Storage devices ... Vendor: Linux Model: File-Stor Gadget Rev: 0314 ... Type: Direct-Access ANSI SCSI revision: 02 ... SCSI device sda: 8192 512-byte hdwr sectors (4 MB) ... sda: Write Protect is off ... SCSI device sda: 8192 512-byte hdwr sectors (4 MB) ... sda: Write Protect is off ... sda: sda1 ... sd 1:0:0:0: Attached scsi disk sda ... sd 1:0:0:0: Attached scsi generic sg0 type 0
- then mount the device and enjoy file sharing:
$ sudo mount /dev/sda1 /mnt/tmp $ cd /mnt/tmp $ showimage /mnt/tmp/test.jpg
To emulate a serial link
- On your Host PC:
$ sudo modprobe usbserial vendor=0x0525 product=0xA4A6
or you can automate it by modifying /etc/modprobe.d/options file (Tested on *Ubuntu):
# vim /etc/modprobe.d/options ... options usbserial vendor=0x0525 product=0xA4A6
- on your APF:
# mknod /dev/ttygserial c 127 0 (if not already existing) # modprobe g_serial gs_bind: Gadget Serial v2.2 bound gs_module_init: Gadget Serial v2.2 loaded
- then connect the USB cable between your PC and your APF and you should see on your Host:
# tail -f /var/log/messages Nov 27 22:53:50 ... usb 1-1.4: new full speed USB device using uhci_hcd and address 7 Nov 27 22:53:50 ... usb 1-1.4: configuration #1 chosen from 1 choice Nov 27 22:53:50 ... usbserial_generic 1-1.4:1.0: generic converter detected Nov 27 22:53:50 ... usb 1-1.4: generic converter now attached to ttyUSB0
- you should now be able to send/receive data through /dev/ttyUSB0 (PC) and /dev/ttygserial (APF):
[armadeus]$ echo "COUCOU" > /dev/ttyUSB0
# cat /dev/ttygserial COUCOUC
To emulate an Ethernet link
- On your Target:
# modprobe g_ether ether gadget: using random self ethernet address ether gadget: using random host ethernet address usb0: Ethernet Gadget, version: May Day 2005 usb0: using imx_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep4in-int usb0: MAC be:df:31:95:16:e0 usb0: HOST MAC 3e:86:1e:94:eb:84 usb0: RNDIS ready
- On your PC:
# modprobe cdc_ether
- If someone knows how to go further.... :-)