Search results

Create the page "Power" on this wiki! See also the search results found.

Page title matches

• Power management
  Power consumption measurements have been done on an APF9328 board. {| border="1" cellpadding="5" cellspacing="0" summary="How to reduce chips power consumption"
  5 KB (693 words) - 09:35, 1 July 2016
• Development boards power supply
  ...'''+ is in the middle of the connector, - on the side'''. Use a regulated power supply capable of providing at least 500mA at minimum required voltage.}}
  1 KB (242 words) - 09:13, 1 July 2015

Page text matches

• Setup
  # Connect the power supply to your development board. (See the [[Datasheet]] of your *Dev board
  3 KB (476 words) - 15:11, 4 June 2019
• Linux start screenshot
  Power Management for Freescale i.MX2x
  13 KB (1,753 words) - 20:03, 7 March 2009
• BootLoader
  ...to save your changes in flash with '''saveenv''' to have them available at power up !
  6 KB (957 words) - 16:30, 13 May 2015
• BootStrap
  2] Power off your board, close all serial terminal sessions, remove all USB cables 4] Power on your board
  11 KB (1,731 words) - 16:31, 6 May 2020
• Framebuffer
  * To leave Framebuffer sleep power mode:
  4 KB (604 words) - 13:16, 18 January 2023
• DAC
  power down or set DAC output with value 0 - 1023
  894 bytes (143 words) - 23:56, 27 October 2009
• PS/2
  Your Armadeus board allows you to connect it a PC keyboard, by using the power of the Spartan3 FPGA (if present on your board). * If your keyboard supports 3,3v power supply you don't need to use the resistor divider brige ! Just use 3,3v fro
  2 KB (348 words) - 21:33, 1 August 2010
• Target Software Installation
  Do not forget to save your changes in FLASH, to have them available at next power up: ...fied with your firmware, you can write it in flash make it "autoloaded" at power up:
  19 KB (2,783 words) - 09:46, 9 September 2021
• Association
  * No accessories (RS-232/USB/Ethernet cables, power supply, ...) are delivered with the boards. If you don't already have them,
  3 KB (478 words) - 13:00, 26 May 2021
• LQ057
  This is a 320x240 18bits TFT module. Backlight power supply should be provided externally (12V DC).
  2 KB (243 words) - 16:38, 27 May 2009
• RTC
  ...(with integrated quartz) on the I2C bus). Do not forget to provide the two power-supply (VCC and Vbackup)). ...isn't button-lithium backup battery under APF28dev board, if we unplug the power, clock is not saved and then we could ask : what the interest of RTC if not
  6 KB (895 words) - 15:47, 19 September 2016
• MTF-T035
  ...forget to check the 3.3V supply polarity on the LCD_adapt board before to power up the system !}}
  3 KB (477 words) - 15:21, 1 July 2015
• MemberList
  ...|| 2 || electronics, board design, embedded software, FPGA, robotics, low power |[[User:SebastienVC|Sébastien Van Cauwenberghe]] || 2 || 2 || 2 || 0 || Power Electronics, Embedded Systems, FPGA's
  9 KB (763 words) - 12:53, 20 December 2013
• Max5821
  power down or set DAC output with value 0 - 1023
  2 KB (257 words) - 14:15, 15 August 2010
• BackLight
  brightness power uevent
  2 KB (337 words) - 00:17, 19 July 2017
• ISE WebPack installation on Linux
  * Enjoy the power of Xilinx tools.
  4 KB (686 words) - 11:57, 20 January 2022
• Scheduling periodic tasks
  ...ple to poweroff your APF everyday at midnight (if your APF can control its power supply):
  3 KB (368 words) - 10:21, 8 July 2013
• GPS
  ...ess" jumper J42 on your [[APF51Dev]] (near microSD connector) '''AND''' to power on FPGA Bank 3 (with corresponding jumper J39). * Power on your GPS module
  6 KB (924 words) - 14:50, 29 March 2017
• Environment
  [[Power management]]
  117 bytes (15 words) - 13:46, 22 January 2008
• Power management
  Power consumption measurements have been done on an APF9328 board. {| border="1" cellpadding="5" cellspacing="0" summary="How to reduce chips power consumption"
  5 KB (693 words) - 09:35, 1 July 2016

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)