Difference between revisions of "Libertas driver"
From ArmadeusWiki
(→Installation) |
(Move PPS specific part to PPS page) |
||
| Line 75: | Line 75: | ||
# ifconfig eth1 up | # ifconfig eth1 up | ||
ADDRCONF(NETDEV_UP): eth1: link is not ready | ADDRCONF(NETDEV_UP): eth1: link is not ready | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</pre> | </pre> | ||
Revision as of 20:27, 1 March 2011
The libertas driver is a collection of modules providing support for Marvell Technology Group's Libertas chipsets. On this page we will only detail the setup of the driver for the SDIO interface modules compatible with 88w8686 chipset, used for example on the APF27's wireless extension board or on APF27_PPS devt board.
The Linux drivers are available since 2.6.24 kernel, thanks to the community effort to rewrite Marvell's proprietary drivers.
Contents
Installation
- Libertas drivers are already installed on your rootfs (if you built it with an APF27/PPS/APF51 as target). If not, it's explained here.
- The drivers require 2 proprietary firmware to be downloaded to the chipset before use. If not already present in /lib/firmware/, here is the procedure to follow:
Firmware (manual install)
These firmware can be manually downloaded and installed:
- get them from David's Woodhouse linux-firmware git repository:
$ cd somewhere_with_free_space/ $ git clone git://git.kernel.org/pub/scm/linux/kernel/git/dwmw2/linux-firmware.git linux-firmware_git
- copy them (version v8) to you TFTP directory (here /tftpboot/):
$ cp linux-firmware_git/libertas/sd8686_v8.bin /tftpboot/ $ cp linux-firmware_git/libertas/sd8686_v8_helper.bin /tftpboot/
- install them on your target (here 192.168.1.2 is my Host IP address):
# mkdir -p /lib/firmware/ # cd /lib/firmware/ # tftp -g -r sd8686_v8.bin -l sd8686.bin 192.168.1.2 # tftp -g -r sd8686_v8_helper.bin -l sd8686_helper.bin 192.168.1.2 # ls -al /lib/firmware/ drwxr-xr-x 2 root root 0 Jan 1 01:01 . drwxr-xr-x 4 root root 0 Dec 30 2009 .. -rw-r--r-- 1 root root 122800 Jan 1 01:00 sd8686.bin -rw-r--r-- 1 root root 2464 Jan 1 01:01 sd8686_helper.bin
 |
Note: You can also try official firmwares got at Marvell website (see Links above) |
Firmware (automatic install)
$ make menuconfig
Package Selection for the target --->
Hardware handling / blockdevices and filesystem maintenance --->
[*] linux-firmware --->
...
*** WiFi chipsets ***
[*] Marvell's 88W8686 (Libertas)
[*] SDIO
Firmware version (v9) --->
[ ] GSPI
$ make
reflash your rootfs
Usage
- Load driver:
# modprobe libertas_sdio lib80211: common routines for IEEE802.11 drivers libertas_sdio: Libertas SDIO driver libertas_sdio: Copyright Pierre Ossman libertas_sdio mmc1:0001:1: firmware: requesting sd8686_helper.bin libertas_sdio mmc1:0001:1: firmware: requesting sd8686.bin libertas: 00:19:88:11:2d:b8, fw 0.70.8p0, cap 0x00000000 eth1 (libertas_sdio): not using net_device_ops yet libertas: eth1: Marvell WLAN 802.11 adapter
If it's not working, you can activate debug like this to report your problem:
# modprobe libertas libertas_debug=0xffffffff # modprobe libertas_sdio
- Bring up the corresponding network interface:
# ifconfig eth1 up ADDRCONF(NETDEV_UP): eth1: link is not ready
Going further
- Now you can use the general instructions here to setup your WiFi network (replace wlan0 with eth1)
