Search results

Create the page "APF27dev" on this wiki! See also the search results found.

Page title matches

• APF27Dev
  * The APF27Dev DVI/HDMI output may not work correctly: due to a hardware issue on the Powe
  2 KB (246 words) - 14:53, 19 March 2021
• Light-APF27Dev
  The apf27dev PCB design will be reused; surface will be divided by 2 to speed developmen Maximum of I/Os and ports must be available on light-apf27dev :
  960 bytes (152 words) - 11:15, 14 December 2009

Page text matches

• Setup
  # '''On APF9328Dev/APF27Dev/PPS:''' connect your PC (= "the Host") to your board with a [http://en.wiki
  3 KB (476 words) - 15:11, 4 June 2019
• BootStrap
  || [[Image:bootstrap_jumper_apf27.jpg|thumb|right|On the [[APF27Dev]] (J12)]]
  11 KB (1,731 words) - 16:31, 6 May 2020
• GPIO Driver
  * Blinks the LED on [[APF27Dev]] (pin 14 of portF):
  7 KB (1,085 words) - 17:41, 12 December 2011
• USB Gadget
  ...sing its USB Device port ([[APF9328DevFull]]), a modified USB host port ([[APF27Dev]]), or an USB OTG port put in device mode ([[APF27 PPS]], [[APF51Dev]], [[A === Hardware specifics for the APF27Dev ===
  7 KB (1,087 words) - 21:23, 31 March 2020
• MultiMediaCard
  * with an [[APF27Dev]], an [[APF28Dev]], an [[APF51Dev]] or an [[APF6Dev]], you can use the onbo
  6 KB (993 words) - 14:54, 7 July 2020
• Hardware
  * [[APF27Dev]]: full featured development board for the APF27 (with several options) ...ion_board|APW wireless board]]: Add WiFi & Bluetooth & GPS & GSM to your [[APF27Dev]]
  2 KB (341 words) - 14:14, 22 August 2018
• MMC/SD
  == On APF9328DevLight 2.0, APF27Dev, APF51Dev & APF28Dev boards, there is already a microSD connector ==
  7 KB (813 words) - 10:36, 22 July 2012
• LCD
  * [[Chimey LW700 |LW700AT (800x480) TFT ]] (old default APF27Dev/APF51Dev LCD, no more sold by Armadeus Systems) * [[Santek ST070015 |ST070015 (800x480) TFT ]] <strong> (Default APF27Dev/APF51Dev/APF28Dev 256k colors TFT sold by Armadeus Systems)</strong>
  3 KB (390 words) - 16:43, 13 July 2015
• ADC max1027
  ...PI will refer to spi1.0 in case of an APF9328 and to spi0.0 in case of the APF27Dev. ==MAX1027 on APF27Dev board==
  10 KB (1,519 words) - 18:03, 18 February 2011
• PWM
  export PWM_CHIP=pwmchip0 (on APF9328Dev/APF27Dev/APF51Dev/APF28Dev/OPOS6UL) export PWM=0 (on APF9328Dev/APF27Dev/APF51Dev/APF6Dev/OPOS6UL)
  5 KB (883 words) - 13:30, 10 February 2022
• RTC
  Currently only Maxim's DS1374 has been tested on [[APF9328Dev]]/[[APF27Dev]] but any I2C RTC, supported by Linux, should work the same way.
  6 KB (895 words) - 15:47, 19 September 2016
• Max5821
  ...s an option on some [[APF9328]] boards. It is mounted in standard on the [[APF27Dev]] development boards. [[Image:Max5821_on_APF27Dev.jpg|thumb|MAX5821 on APF27Dev]]
  2 KB (257 words) - 14:15, 15 August 2010
• Controller Area Network
  CAN bus is available on the [[APF9328DevFull]] and [[APF27Dev]] (both as an option) and on the [[APF51Dev]] (by default). ...v_with_MCP2515.jpg|center|thumb|'''figure 1''' - ''MCP2515 localisation on APF27Dev'']]
  2 KB (238 words) - 11:04, 18 April 2011
• ALSA
  ...(like the [[TSC2102]] on the [[APF9328DevFull]], the [[TSC2101]] on the [[APF27Dev]], the WM8960 on the [[APF51Dev]] or the SGTL5000 on the [[APF6Dev]]) throu
  11 KB (1,653 words) - 18:09, 30 July 2018
• USB Host
  * [[APF27]] and [[APF27Dev]]: two Host ports are available. The controllers are integrated in the i.MX
  5 KB (749 words) - 12:04, 23 April 2015
• Power management
  [ ] Use D14 LED of the APF27Dev for suspend signaling [ ] Use S1 switch of the APF27Dev to resume after a suspend
  5 KB (693 words) - 09:35, 1 July 2016
• A simple design with Wishbone bus
  {{Note| On [[APF27Dev]] and [[APF51Dev]] a button is already soldered to a FPGA pin. Just don't f
  10 KB (1,574 words) - 12:43, 30 June 2022
• LQ043 Adapt
  ! ''' ''' || '''APF27Dev''' || '''OPOS6ULDev''' || '''APF9328DevFull''' || '''APF9328DevLightV1''' | ...the LCD_Adapt [[Image:LQ043_Adapt_to_APF27Dev.jpg|thumb|Connection between APF27Dev and LQ043_Adapt]] || flat cable (1) connected between TFT_J23 connector of
  4 KB (600 words) - 17:50, 13 March 2017
• APF27
  Here is a list of the main features and options available on the APF27 and APF27dev: | style="text-align:center;" | '''APF27dev'''
  9 KB (1,132 words) - 09:39, 12 February 2015
• AS1531
  * On the [[APF27Dev]] board it can be soldered on SPI3 bus, which is available on connector J8.
  3 KB (397 words) - 20:13, 12 February 2013

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)