Difference between revisions of "LinuxInstall"
m (→Get Armadeus software) |
(→Get Armadeus software) |
||
(137 intermediate revisions by 14 users not shown) | |||
Line 4: | Line 4: | ||
The installation was successfully tested on the following distributions: | The installation was successfully tested on the following distributions: | ||
− | * Debian | + | * Debian Lenny (5.0), Squeeze (6.0.x), Wheezy (7.2), Jessie (8.0) |
− | * | + | * X/KUbuntu Edgy Eft (6.10), Gutsy Gibbon (7.10), Hardy Heron (8.04) & Jaunty Jackalope (9.04) |
− | + | * Ubuntu Lucid Lynx (10.04) (32 & 64bits), 12.04 LTS (32 & 64bits), 13.10 (32 & 64bits), 14.04, 15.04 & 16.04 | |
− | + | * LUbuntu 17.10 | |
* Mandriva 2006 | * Mandriva 2006 | ||
− | * | + | * Fedora Core 3 & 4, Fedora 10, Laughlin (14) |
− | * | + | * Red Hat Enterprise 5.2 |
− | * | + | * Gentoo 10.0 (32 & 64 bits) |
+ | * SuSE 10.1, OpenSUSE 11.3 - 12.3 | ||
+ | '''The installation may fail on:''' | ||
+ | * Ubuntu Karmic Koala (9.10): tslib fails to build | ||
+ | |||
+ | '''APF28 requirements:''' | ||
+ | * APF28 board requires a Linux distribution with (GNU) tar version 1.20 or later to compile the Linux Kernel - Please update or upgrade your Linux distribution. | ||
==Prerequisites for Linux installation== | ==Prerequisites for Linux installation== | ||
Line 22: | Line 28: | ||
</pre> | </pre> | ||
}} | }} | ||
− | + | For armadeus up to 3.4, make should be '''strictly''' make-3.81 (make-3.82 is too strict). A Fedora (14 and 15) -specific solution can be found later; other recent distributions such as mageia1 also have make-3.82, and a generic solution, based on configure&& make&& sudo make install can be used to install make-3.81 (which can be retrieved from http://ftp.gnu.org/gnu/make/make-6.81.tar.gz) in /usr/local/bin (and , according to one's PATH, make 3-81 can be invoked directly or as /usr/local/bin/make). | |
− | Depending on your distribution, some additional packages are required | + | |
+ | Depending on your distribution, some additional packages are required: | ||
===Debian/Ubuntu based systems=== | ===Debian/Ubuntu based systems=== | ||
− | + | [[Ubuntu/Debian installation prerequisites]] | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
===Mandriva based systems=== | ===Mandriva based systems=== | ||
− | + | [[Mandriva installation prerequisites]] | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ===RPM-based systems (RedHat, Fedora, CentOS)=== | |
− | + | [[RedHat/Fedora installation prerequisites]] | |
− | + | ||
− | + | ||
− | === | + | ===OpenSuse based systems=== |
− | + | [[OpenSuse installation prerequisites]] | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ===Gentoo based systems=== | |
− | + | [[Gentoo installation prerequisites]] | |
− | + | ||
− | + | ||
==Get Armadeus software== | ==Get Armadeus software== | ||
− | * '''If you are a "careful" user''', then download [ | + | * '''If you are a "careful" user''', then download [https://gitlab.com/armadeus/armadeus-bsp/-/tags the latest stable installation tarball from gitlab] and detar it wherever you want: |
<pre class="host"> | <pre class="host"> | ||
− | $ tar xjvf armadeus- | + | $ tar xjvf armadeus-7.0.tar.bz2 |
</pre> | </pre> | ||
− | * | + | * '''If you want the latest snapshot or if you have a recent SOM ([[OPOS6UL]]/[[OPOS8MM]])''', the whole development tree can be checked out from our [[GIT]] repository. |
<pre class="host"> | <pre class="host"> | ||
− | $ git clone git: | + | $ git clone git@gitlab.com:armadeus/armadeus-bsp.git armadeus |
− | </pre> | + | </pre> |
− | + | * depending on your previous choice, a directory named ''armadeus/'' or ''armadeus-7.0/'' will be created on your hard-disk and will contain all the files you need. | |
'''Remarks''': | '''Remarks''': | ||
* '''Do not use spaces''' in the directory name ! | * '''Do not use spaces''' in the directory name ! | ||
− | * GIT write/push | + | * '''Do not use a directory path beginning with /usr.''' It is a known bug of Buildroot (until BR2012.11, at 2012-12). |
+ | * GIT write/push accesses are limited to the integrators ([[User:JulienB|JulienB]], [[User:SebastienSz|SebastienSz]], [[User:Jorasse|Jorasse]], [[User:FabienM|FabienM]], [[User:SebastienR|SebastienR]]) | ||
− | ==Configure SDK options== | + | ==Configure SDK/BSP options== |
− | The first time you compile an Armadeus distribution you have to specify the target to work with. | + | {{Note|If you are new to Armadeus and have troubles compiling armadeus-5.x/armadeus-6.x using the following instructions, you may find some hints here: [[Releases]]}} |
+ | *Go to the directory where you put the Armadeus sources: | ||
+ | <pre class="host"> | ||
+ | $ cd armadeus/ (or armadeus-7.0/) | ||
+ | </pre> | ||
+ | *The first time you compile an Armadeus distribution you have to specify the target (here the [[APF9328]]) to work with. | ||
<pre class="host"> | <pre class="host"> | ||
− | |||
$ make apf9328_defconfig | $ make apf9328_defconfig | ||
</pre> | </pre> | ||
− | This command reloads the default configuration to support | + | This command reloads the default configuration to support your target and automatically start a Buildroot's configuration menu. |
+ | |||
+ | * Current valid default configurations are: | ||
<pre class="host"> | <pre class="host"> | ||
− | + | apf9328_defconfig apf27_defconfig pps_defconfig apf28_defconfig apf51_defconfig pps51_defconfig apf6_defconfig apf6legacy_defconfig opos6ul_defconfig opos6ulnano_defconfig | |
</pre> | </pre> | ||
+ | {{Note| To get the full list of available config just type make, it will download buildroot and print following message : | ||
+ | <pre class="host"> | ||
+ | $ make | ||
+ | [...] | ||
+ | System not configured. Use make <board>_defconfig | ||
+ | armadeus valid configurations are: | ||
+ | opos6ul_legacy_defconfig opos6ulnano-preempt-rt_defconfig apf6_defconfig pps_defconfig opos6ultest_defconfig apf51_defconfig opos6ulsp_defconfig apf6dawnsmalllinux_defconfig apf27preempt-rt_defconfig apf27test_defconfig apf27_defconfig apf28legacytest_defconfig opos6ullegacy-4.14_defconfig opos6ulnano_defconfig apf28legacy_defconfig apf6mainline-4.19_defconfig opos6ul_defconfig apf6legacy_defconfig apf6xenomai_defconfig apf51test_defconfig opos6ul-preempt-rt_defconfig apf6legacy-preempt-rt_defconfig apf6legacy-4.1_defconfig pps51_defconfig apf6mainline-4.9_defconfig apf28test_defconfig apf28_defconfig apf6mediacenter_defconfig opos6ullegacy-4.9_defconfig opos6ul_recovery_defconfig apf6failsafe_defconfig apf6test_defconfig opos6ullegacy-4.1_defconfig apf27xenomai_defconfig | ||
+ | |||
+ | Makefile:129: recipe for target '/usr/local/projects/apf6_sp_419/buildroot/.configured' failed | ||
+ | make: *** [/usr/local/projects/apf6_sp_419/buildroot/.configured] Error 1 | ||
+ | </pre> | ||
+ | }} | ||
− | {{Note|If you ever made changes | + | For PPS boards, please see [[APF27_PPS]] or [[PPS51]] Wiki pages, as these boards have specific build. |
+ | |||
+ | * After some downloads, you will get the Buildroot configuration interface: | ||
+ | |||
+ | {{Note|If you ever made changes during the following steps, at any time, you can reload the default configuration with: | ||
+ | $ make xxx_defconfig (xxx depending on your module name)}} | ||
[[Image:Menuconfig3.png]]<br> | [[Image:Menuconfig3.png]]<br> | ||
Line 118: | Line 110: | ||
*# for more Help about Buildroot commands, select "Help" in the main configuration screen | *# for more Help about Buildroot commands, select "Help" in the main configuration screen | ||
− | * | + | * Update the memory configuration of your board ('''if needed'''; by default BSP is configured for the minimal memory configuration available on the corresponding board): |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | :In menu: | |
− | <pre class="config"> | + | :<pre class="config">System configuration ---> [*] Armadeus Device Support ---></pre> |
− | + | ||
− | + | ||
− | + | ||
− | + | :you can check and change the quantity of RAM available on your Armadeus board: | |
− | + | :[[Image:Build_config_memory.png]] | |
− | + | :For [[APF9328]] the memory can be either 16 or 32MiB (be sure to select 1 RAM chip) | |
− | + | :For [[APF27]] it could be either 64MiB or 128MiB (2 x 64MiB) (in that case be sure to select 2 chips of 64MiB instead of 1 chip of 128MiB). | |
− | + | :For [[APF51]] it could be either 256MiB or 512MiB (2x256MiB) (in such case be sure to select 2 chips of 256MiB instead of 1 chip of 512). | |
+ | :For [[APF28]] The memory can be 128, 256, 512 or 1024MiB (be sure to select 1 RAM chip). | ||
+ | :For [[APF6]]/[[APF6SP]] The memory can be 512 Mbytes or 1Gbytes with ram chip size of 512Mbytes. | ||
+ | :For [[OPOS6UL]]/[[OPOS6UL_NANO]] The memory size is automatically detected so you don't care ;-) | ||
− | * | + | * You may decrease the compilation time by increasing the number of parallel jobs running simultaneously on your system (the result is not guaranteed). This option is located in: |
− | <pre class="config"> | + | :<pre class="config">Build Options ---> (0) Number of jobs to run simultaneously</pre> |
− | + | 0 means that Buildroot will try to guess automatically how much parallel jobs it can launch. | |
− | + | ||
− | </pre> | + | |
− | + | ||
− | + | * During the SDK/BSP build, a lot of software archives are downloaded from Internet. The downloaded files are put by default in the ''armadeus/downloads/'' directory. '''If you have several views or plan to build the toolchain several times''', we advise you to put all the downloaded files in ''/local/downloads'' (for example). This is done by configuring Buildroot to use this directory for all your views. Nevertheless, Buildroot will be downloaded separately for each build environment you set up. | |
− | + | :<pre class="config">Build options ---> (...) Download dir</pre> | |
− | + | :[[Image:Build_config_download.png]] | |
− | + | {{Note|Of course, ''/local/downloads'' should exists on your system and you should have writing rights on it !}} | |
− | + | * In recent Buildroot you can also use the following method: | |
− | * During the | + | export BR2_DL_DIR=/local/downloads |
− | <pre class="config"> | + | |
− | Build options ---> | + | |
− | + | ||
− | </pre> | + | |
− | [[Image: | + | |
− | + | ||
− | * After the build, we advise you | + | * After the build, we advise you to copy all the files in ''downloads/'' / ''/local/downloads'' on a removable medium, in case you want to install the development tools on other systems, without to have to reload all the archives. |
* Now, Exit the configuration tool and save your configuration | * Now, Exit the configuration tool and save your configuration | ||
+ | |||
+ | * You can come back to this configuration menu, by typing (your changes will be kept): | ||
+ | <pre class="host"> | ||
+ | make menuconfig | ||
+ | </pre> | ||
==Launch build== | ==Launch build== | ||
Line 165: | Line 148: | ||
The toolchain and the full distribution are automatically built. During this procedure, several files are downloaded from Internet. <br> | The toolchain and the full distribution are automatically built. During this procedure, several files are downloaded from Internet. <br> | ||
'''Please wait for a while.... it takes at least one hour for the first run!'''<br> | '''Please wait for a while.... it takes at least one hour for the first run!'''<br> | ||
− | + | By default, the downloaded files/tarball are put in the ''armadeus/downloads/'' directory. Please see the previous chapter to know how to optimize that if you plan to build several views or want to build faster. | |
==Enjoy the result== | ==Enjoy the result== | ||
− | The generated binary files can be found in the subdirectory ''buildroot/ | + | The generated binary files can be found in the subdirectory ''buildroot/output/images'': |
+ | *''apf9328-u-boot.brec'' (only on [[APF9328]]): BRecord image that can be used with the bootstrap, if U-Boot is not installed or not working (see [[BootLoader]] page) | ||
+ | *''xxx-u-boot.bin'': U-Boot image file to be used with U-Boot itself, (see [[BootLoader#Update_U-Boot | updating U-Boot]]) | ||
+ | *''xxx-linux.bin'': Linux image to use with U-Boot, (see [[Target_Software_Installation#Linux_kernel_installation | updating Linux]]) | ||
+ | *''xxx-rootfs.jffs2'': JFFS2 filesystem/rootfs image to use with U-Boot, (see [[Target_Software_Installation#Linux_rootfs_installation | updating rootfs]]) | ||
+ | *''xxx-rootfs.ubi'' (not supported on [[APF9328]]): [[UBIFS|UBI]] filesystem/rootfs image to use with U-Boot, (see [[Target_Software_Installation#Linux_rootfs_installation | updating rootfs]]) | ||
+ | *''xxx-rootfs.ext4'': EXT4 filesystem/rootfs image to use with U-Boot, (on [[APF6]] and [[OPOS6UL]]) | ||
+ | *''xxx-rootfs.tar'': for an NFS/MMC based rootfs, (see [[Network_Configuration#Boot_from_NFS | Booting from NFS]] & [[MultiMediaCard#Booting_from_MMC.2FSD | Booting from a MMC/SD]]) | ||
− | + | '''Please note the new naming convention of binary files and directories (since Armadeus 4.0)''' | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | ''' | + | *''buildroot/output/build'': contains all the build results for target root filesystem, Linux, Busybox and U-Boot... |
+ | *''buildroot/output/toolchain/'': cross compilation toolchain's build dir. Binaries usable for cross-compilation are in ''buildroot/output/host/usr/bin''. | ||
+ | *''buildroot/output/target/'': target filessytem before generating rootfs images | ||
− | + | More information is available in the [http://buildroot.uclibc.org/buildroot.html Buildroot's documentation] | |
− | + | ||
− | + | ||
− | + | ||
− | + | * Note: Previous versions (3.x) of Armadeus SDK stored the generated binary files at a different place: '' ''buildroot/binaries/XX/'' (where XX was the name of your board). | |
− | + | <noinclude> | |
− | + | You then copy the binary image to your server directory: | |
− | + | <pre class="host"> | |
− | : | + | $ cp buildroot/output/images/* /tftpboot |
− | + | </pre> | |
− | + | ||
− | |||
==To keep your local copy/repository up-to-date with the armadeus GIT repository== | ==To keep your local copy/repository up-to-date with the armadeus GIT repository== | ||
<pre class="host"> | <pre class="host"> | ||
Line 205: | Line 188: | ||
You can do a: | You can do a: | ||
− | $ make | + | $ make apfXX_defconfig |
to have the latest features automatically activated. | to have the latest features automatically activated. | ||
Line 215: | Line 198: | ||
$ rm Makefile | $ rm Makefile | ||
$ git pull | $ git pull | ||
− | $ make | + | $ make apfXX_defconfig |
$ make | $ make | ||
+ | $ cp buildroot/output/images/* /tftpboot | ||
Enjoy! | Enjoy! | ||
− | |||
− | |||
</noinclude> | </noinclude> |
Latest revision as of 15:12, 30 January 2024
How-To install Armadeus Software Development Kit (SDK) on Linux systems. This SDK is currently based on the (excellent) Buildroot.
The installation was successfully tested on the following distributions:
- Debian Lenny (5.0), Squeeze (6.0.x), Wheezy (7.2), Jessie (8.0)
- X/KUbuntu Edgy Eft (6.10), Gutsy Gibbon (7.10), Hardy Heron (8.04) & Jaunty Jackalope (9.04)
- Ubuntu Lucid Lynx (10.04) (32 & 64bits), 12.04 LTS (32 & 64bits), 13.10 (32 & 64bits), 14.04, 15.04 & 16.04
- LUbuntu 17.10
- Mandriva 2006
- Fedora Core 3 & 4, Fedora 10, Laughlin (14)
- Red Hat Enterprise 5.2
- Gentoo 10.0 (32 & 64 bits)
- SuSE 10.1, OpenSUSE 11.3 - 12.3
The installation may fail on:
- Ubuntu Karmic Koala (9.10): tslib fails to build
APF28 requirements:
- APF28 board requires a Linux distribution with (GNU) tar version 1.20 or later to compile the Linux Kernel - Please update or upgrade your Linux distribution.
Contents
Prerequisites for Linux installation
Note: From here we assume that your Linux system has a make version greater or equal to 3.81. To check it:
$ make -v GNU Make 3.81 ... |
For armadeus up to 3.4, make should be strictly make-3.81 (make-3.82 is too strict). A Fedora (14 and 15) -specific solution can be found later; other recent distributions such as mageia1 also have make-3.82, and a generic solution, based on configure&& make&& sudo make install can be used to install make-3.81 (which can be retrieved from http://ftp.gnu.org/gnu/make/make-6.81.tar.gz) in /usr/local/bin (and , according to one's PATH, make 3-81 can be invoked directly or as /usr/local/bin/make).
Depending on your distribution, some additional packages are required:
Debian/Ubuntu based systems
Ubuntu/Debian installation prerequisites
Mandriva based systems
Mandriva installation prerequisites
RPM-based systems (RedHat, Fedora, CentOS)
RedHat/Fedora installation prerequisites
OpenSuse based systems
OpenSuse installation prerequisites
Gentoo based systems
Gentoo installation prerequisites
Get Armadeus software
- If you are a "careful" user, then download the latest stable installation tarball from gitlab and detar it wherever you want:
$ tar xjvf armadeus-7.0.tar.bz2
- If you want the latest snapshot or if you have a recent SOM (OPOS6UL/OPOS8MM), the whole development tree can be checked out from our GIT repository.
$ git clone git@gitlab.com:armadeus/armadeus-bsp.git armadeus
- depending on your previous choice, a directory named armadeus/ or armadeus-7.0/ will be created on your hard-disk and will contain all the files you need.
Remarks:
- Do not use spaces in the directory name !
- Do not use a directory path beginning with /usr. It is a known bug of Buildroot (until BR2012.11, at 2012-12).
- GIT write/push accesses are limited to the integrators (JulienB, SebastienSz, Jorasse, FabienM, SebastienR)
Configure SDK/BSP options
Note: If you are new to Armadeus and have troubles compiling armadeus-5.x/armadeus-6.x using the following instructions, you may find some hints here: Releases |
- Go to the directory where you put the Armadeus sources:
$ cd armadeus/ (or armadeus-7.0/)
- The first time you compile an Armadeus distribution you have to specify the target (here the APF9328) to work with.
$ make apf9328_defconfig
This command reloads the default configuration to support your target and automatically start a Buildroot's configuration menu.
- Current valid default configurations are:
apf9328_defconfig apf27_defconfig pps_defconfig apf28_defconfig apf51_defconfig pps51_defconfig apf6_defconfig apf6legacy_defconfig opos6ul_defconfig opos6ulnano_defconfig
For PPS boards, please see APF27_PPS or PPS51 Wiki pages, as these boards have specific build.
- After some downloads, you will get the Buildroot configuration interface:
Note: If you ever made changes during the following steps, at any time, you can reload the default configuration with:
$ make xxx_defconfig (xxx depending on your module name) |
- If you are not familiar with Buildroot here are some tips:
- you can move the highlighted item with the "up"/"down" arrow keys
- with the "left"/"right" arrow keys you can choose between "Select", "Exit" or "Help" buttons
- "space"/"enter":
- selects the currently highlighted item if you are on the "Select" button
- go back in previous menu if you are on "Exit" button
- show you some Help for current item if you are on "Help" button
- for more Help about Buildroot commands, select "Help" in the main configuration screen
- Update the memory configuration of your board (if needed; by default BSP is configured for the minimal memory configuration available on the corresponding board):
- In menu:
System configuration ---> [*] Armadeus Device Support --->
- you can check and change the quantity of RAM available on your Armadeus board:
- For APF9328 the memory can be either 16 or 32MiB (be sure to select 1 RAM chip)
- For APF27 it could be either 64MiB or 128MiB (2 x 64MiB) (in that case be sure to select 2 chips of 64MiB instead of 1 chip of 128MiB).
- For APF51 it could be either 256MiB or 512MiB (2x256MiB) (in such case be sure to select 2 chips of 256MiB instead of 1 chip of 512).
- For APF28 The memory can be 128, 256, 512 or 1024MiB (be sure to select 1 RAM chip).
- For APF6/APF6SP The memory can be 512 Mbytes or 1Gbytes with ram chip size of 512Mbytes.
- For OPOS6UL/OPOS6UL_NANO The memory size is automatically detected so you don't care ;-)
- You may decrease the compilation time by increasing the number of parallel jobs running simultaneously on your system (the result is not guaranteed). This option is located in:
Build Options ---> (0) Number of jobs to run simultaneously
0 means that Buildroot will try to guess automatically how much parallel jobs it can launch.
- During the SDK/BSP build, a lot of software archives are downloaded from Internet. The downloaded files are put by default in the armadeus/downloads/ directory. If you have several views or plan to build the toolchain several times, we advise you to put all the downloaded files in /local/downloads (for example). This is done by configuring Buildroot to use this directory for all your views. Nevertheless, Buildroot will be downloaded separately for each build environment you set up.
Note: Of course, /local/downloads should exists on your system and you should have writing rights on it ! |
- In recent Buildroot you can also use the following method:
export BR2_DL_DIR=/local/downloads
- After the build, we advise you to copy all the files in downloads/ / /local/downloads on a removable medium, in case you want to install the development tools on other systems, without to have to reload all the archives.
- Now, Exit the configuration tool and save your configuration
- You can come back to this configuration menu, by typing (your changes will be kept):
make menuconfig
Launch build
$ make
The toolchain and the full distribution are automatically built. During this procedure, several files are downloaded from Internet.
Please wait for a while.... it takes at least one hour for the first run!
By default, the downloaded files/tarball are put in the armadeus/downloads/ directory. Please see the previous chapter to know how to optimize that if you plan to build several views or want to build faster.
Enjoy the result
The generated binary files can be found in the subdirectory buildroot/output/images:
- apf9328-u-boot.brec (only on APF9328): BRecord image that can be used with the bootstrap, if U-Boot is not installed or not working (see BootLoader page)
- xxx-u-boot.bin: U-Boot image file to be used with U-Boot itself, (see updating U-Boot)
- xxx-linux.bin: Linux image to use with U-Boot, (see updating Linux)
- xxx-rootfs.jffs2: JFFS2 filesystem/rootfs image to use with U-Boot, (see updating rootfs)
- xxx-rootfs.ubi (not supported on APF9328): UBI filesystem/rootfs image to use with U-Boot, (see updating rootfs)
- xxx-rootfs.ext4: EXT4 filesystem/rootfs image to use with U-Boot, (on APF6 and OPOS6UL)
- xxx-rootfs.tar: for an NFS/MMC based rootfs, (see Booting from NFS & Booting from a MMC/SD)
Please note the new naming convention of binary files and directories (since Armadeus 4.0)
- buildroot/output/build: contains all the build results for target root filesystem, Linux, Busybox and U-Boot...
- buildroot/output/toolchain/: cross compilation toolchain's build dir. Binaries usable for cross-compilation are in buildroot/output/host/usr/bin.
- buildroot/output/target/: target filessytem before generating rootfs images
More information is available in the Buildroot's documentation
- Note: Previous versions (3.x) of Armadeus SDK stored the generated binary files at a different place: buildroot/binaries/XX/ (where XX was the name of your board).
You then copy the binary image to your server directory:
$ cp buildroot/output/images/* /tftpboot
To keep your local copy/repository up-to-date with the armadeus GIT repository
$ git pull
This will update your working directory to the latest release.
Note: if "git pull" fails because a directory or a file already exists, then do:
$ rm -rf <this-directory/file> $ git pull
You can do a:
$ make apfXX_defconfig
to have the latest features automatically activated.
You have to do a make to rebuild binary files and then upload the binary files to your target.
Note: if definitively everything goes wrong while it worked before the last update. You can apply the following procedure (all your modifications in buildroot will be lost):
$ rm -rf buildroot/ $ rm Makefile $ git pull $ make apfXX_defconfig $ make $ cp buildroot/output/images/* /tftpboot
Enjoy!